1 May 2024 in Journal of Instrumentation
The ATLAS detector is installed in its experimental cavern at Point 1 of the CERN Large Hadron Collider. During Run 2 of the LHC, a luminosity of ℒ = 2 × 1034 cm-2 s-1 was routinely achieved at the start of fills, twice the design luminosity. For Run 3, accelerator improvements, notably luminosity levelling, allow sustained running at an instantaneous luminosity of ℒ = 2 × 1034 cm-2 s-1, with an average of up to 60 interactions per bunch crossing. The ATLAS detector has been upgraded to recover Run 1 single-lepton trigger thresholds while operating comfortably under Run 3 sustained pileup conditions. A fourth pixel layer 3.3 cm from the beam axis was added before Run 2 to improve vertex reconstruction and b-tagging performance. New Liquid Argon Calorimeter digital trigger electronics, with corresponding upgrades to the Trigger and Data Acquisition system, take advantage of a factor of 10 finer granularity to improve triggering on electrons, photons, taus, and hadronic signatures through increased pileup rejection. The inner muon endcap wheels were replaced by New Small Wheels with Micromegas and small-strip Thin Gap Chamber detectors, providing both precision tracking and Level-1 Muon trigger functionality. Trigger coverage of the inner barrel muon layer near one endcap region was augmented with modules integrating new thin-gap resistive plate chambers and smaller-diameter drift-tube chambers. Tile Calorimeter scintillation counters were added to improve electron energy resolution and background rejection. Upgrades to Minimum Bias Trigger Scintillators and Forward Detectors improve luminosity monitoring and enable total proton-proton cross section, diffractive physics, and heavy ion measurements. These upgrades are all compatible with operation in the much harsher environment anticipated after the High-Luminosity upgrade of the LHC and are the first steps towards preparing ATLAS for the High-Luminosity upgrade of the LHC. This paper describes the Run 3 configuration of the ATLAS detector.
18 October 2019 in IEEE Transactions on Instrumentation and Measurement
In high energy physics and nuclear physics experiments, particularly the ones based on a particle accelerator, the data rate from the detector is usually in the order of terabytes per second. These high throughput data from detector front-end electronics (FEEs) need to be transmitted to the back-end computing farm for high-level event selection and building. A data acquisition (DAQ) system with the features of high density, scalable, and easily upgradeable is crucial to simplify the readout architecture of the whole experiment. This article will introduce the design of a generic high bandwidth PCIe card, which can be used as the important input–output card in a scalable DAQ system. It can factorize FEEs from data handling and reduce the amount of custom hardware in favor of scalable detector-independent commercial hardware and software. Besides the 48 channels of bidirectional high-speed fiber optical links with front ends, it also supports to synchronize with the experiment timing system and to fan-out the clock and trigger information with a fixed latency to the FEEs.
26 April 2019 in IEEE Transactions on Nuclear Science
During the next major shutdown (2019-2020), the ATLAS experiment at the LHC will adopt the Front-End Link eXchange (FELIX) system as the interface between the data acquisition, detector control and TTC (Timing, Trigger and Control) systems and new or updated trigger and detector front-end electronics. FELIX will function as a router between custom serial links from front-end ASICs and FPGAs to data collection and processing components via a commodity switched network. Links may aggregate many slower links or be a single high bandwidth link. FELIX will also forward the LHC bunch-crossing clock, fixed latency trigger accepts and resets received from the TTC system to front-end electronics. The FELIX system uses commodity server technology in combination with FPGA-based PCIe I/O cards. The FELIX host servers will run a software routing platform serving data to network clients. Commercial off the shelf (COTS) servers connected to FELIX systems via the same network will run the new Software Readout Driver (SW ROD) infrastructure for event fragment building and buffering, with support for detector or trigger specific data processing, and will serve the data upon request to the ATLAS High Level Trigger for Event Building and Selection. This paper will cover the design and status of FELIX, results of early performance testing and integration tests with several ATLAS front-ends.
1 June 2024 in Journal of Instrumentation
TRopIcal DEep-sea Neutrino Telescope (TRIDENT) plans to incorporate silicon photomultipliers (SiPMs) with superior time resolution in addition to photomultiplier tubes (PMTs) into its detection units, namely hybrid Digital Optical Modules (hDOMs), to improve its angular resolution. However, the time resolution significantly degrades for large-area SiPMs due to the large detector capacitance, posing significant challenges for the readout electronics of SiPMs in hDOM. We analyzed the influences of series and parallel connections when constructing a large-area SiPM array and designed a series-parallel connection SiPM array with differential output. We also designed a high-speed pre-amplifier based on transformers (MABA-007159) and radio frequency amplifiers (BGA2803), and an analog multi-channel summing circuit based on operational amplifiers (LMH6629). We measured the single photon time resolution (SPTR) of a 4 × 4 SiPM (Hamamatsu S13360-3050PE) array (12 × 12 mm2) of approximately 300 ps FWHM. This front-end readout design enables the large-area SiPM array to achieve high-precision single photon time measurement in one readout channel.
7 August 2023 in IEEE Transactions on Nuclear Science
The tRopIcal DEep-sea Neutrino Telescope (TRIDENT) is a future large-scale next-generation neutrino telescope. In September 2021, the TRIDENT pathfinder experiment (TRIDENT EXplorer, T-REX for short) completed in-situ measurements of deep-sea water properties in the South China Sea. The T-REX apparatus integrates two independent and complementary systems, a photomultiplier tube and a camera system, to measure the optical and radioactive properties of the deep-sea water. One light emitter module and two light receiver modules were deployed, which were synchronized by using White Rabbit technology. The light emitter module generates nanosecond-width light-emitting diode pulses, while the light receiver module hosts three photomultiplier tubes and a camera to detect photons. The submerged apparatus and the data acquisition system perform real-time command and data transmission. We report the design and performance of the readout electronics for T-REX, including hardware modules, firmware design for digital signal processing, and host-computer software.
14 May 2025 in Journal of High Energy Physics
Detailed studies of two-neutrino double electron capture (2νDEC) is a crucial step towards searching for the neutrinoless mode to explore the Majorana nature of neutrinos. We have measured precisely the half-life of the 2νDEC process in 124Xe, utilizing a total exposure of 1.73 tonne year from the commissioning run and the first science run of the PandaX-4T experiment. A time-dependent background model in the $$ \mathcal{O} $$ (10 keV) energy is constructed for the first time in PandaX-4T data. With an unbinned maximum likelihood fit, we determine the half-life of the 2νDEC process to be (1.03 ± 0.15stat ± 0.08sys) × 1022 yr. Furthermore, we have evaluated the capture fraction for both electrons captured from the K shell (KK) to be (65 ± 5)%, which aligns with the 124Xe nuclear model calculations within 1.8 σ.