3 July 2017 in Organic Process Research & Development
We report the construction and use of a vortex reactor which uses a rapidly rotating cylinder to generate Taylor vortices for continuous flow thermal and photochemical reactions. The reactor is designed to operate under conditions required for vortex generation. The flow pattern of the vortices has been represented using computational fluid dynamics, and the presence of the vortices can be easily visualized by observing streams of bubbles within the reactor. This approach presents certain advantages for reactions with added gases. For reactions with oxygen, the reactor offers an alternative to traditional setups as it efficiently draws in air from the lab without the need specifically to pressurize with oxygen. The rapid mixing generated by the vortices enables rapid mass transfer between the gas and the liquid phases allowing for a high efficiency dissolution of gases. The reactor has been applied to several photochemical reactions involving singlet oxygen (1O2) including the photo-oxidations of α-terpinene and furfuryl alcohol and the photodeborylation of phenyl boronic acid. The rotation speed of the cylinder proved to be key for reaction efficiency, and in the operation we found that the uptake of air was highest at 4000 rpm. The reactor has also been successfully applied to the synthesis of artemisinin, a potent antimalarial compound; and this three-step synthesis involving a Schenk-ene reaction with 1O2, Hock cleavage with H+, and an oxidative cyclization cascade with triplet oxygen (3O2), from dihydroartemisinic acid was carried out as a single process in the vortex reactor.
1 December 2012 in Journal of Wind Engineering and Industrial Aerodynamics
The development of a coupled computational fluid-dynamics rigid body (CFD–RBD) model is presented. The RBD model deploys rotational quaternions, which are free from the gimbal lock that is associated with Euler rotational matrix. The quaternion model means that the complex 3D spinning flight modes associated with the flight of plate-type windborne debris can be modelled robustly. This paper attempts to determine the accuracy of the CFD–RBD model by comparing the predicted trajectories from a large number of debris simulations with experimentally derived equations of best fit. Agreement is found to be good and, based on the findings, an alternative form for the dimensionless flight distance is presented, which extends the range of the experimental study to longer flight times.The predictions from the CFD–RBD model are then compared against two quasi-steady analytical debris flight models. The second model is based on modified force and moment coefficients, which are informed by the findings from the CFD–RBD model. For plates that have attained a stable, autorotational flight mode, the CFD–RBD and analytical models are in good agreement. Their predictions differ during the initial stages of flight, where the complex non-linear interactions between the plate and its wake are not captured by the analytical models
25 March 2010 in Wind and Structures
1 April 2014 in Journal of Fluids and Structures
This paper examines the use of a coupled Computational Fluid Dynamics (CFD) – Rigid Body Dynamics (RBD) model to study the fixed-axis autorotation of a square flat plate. The calibration of the model against existing wind tunnel data is described. During the calibration, the CFD models were able to identify complex period autoration rates, which were attributable to a mass eccentricity in the experimental plate. The predicted flow fields around the autorotating plates are found to be consistent with existing observations. In addition, the pressure coefficients from the wind tunnel and computational work were found to be in good agreement. By comparing these pressure distributions and the vortex shedding patterns at various stages through an autorotation cycle, it was possible to gain important insights into the flow structures that evolve around the plate. The CFD model is also compared against existing correlation functions that relate the mean tip speed ratio of the plate to the aspect ratio, thickness ratio and mass moment of inertia of the plate. Agreement is found to be good for aspect ratios of 1, but poor away from this value. However, other aspects of the numerical modelling are consistent with the correlations
1 December 2012 in Journal of Wind Engineering and Industrial Aerodynamics
A coupled Computational Fluid Dynamics–Rigid Body Dynamics (CFD–RBD) model is presented, which is capable of modelling the 3D flight of plate-type windborne debris. The RBD model is based on rotational quaternions, which means that complex spinning modes of flight can be modelled accurately and robustly. For debris that is free to fly in the absence of obstructions, it is shown that, depending on the initial plate orientation, a number of distinct flight modes are observed. When the plate is aligned at right angles to the flow, the flight mode depends critically on the initial angle of attack. The plate may wobble or flutter as it flies, never completing a full rotation, or it may enter an autorotational flight mode. Depending on the direction of rotation, the plate is capable of flying faster than the wind. It does this by converting some of its potential energy into rotational energy. The rotation of the plate causes the forces acting on the plate to further accelerate or decelerate it, depending on the rotation direction. When the plate is not aligned at right angles to the flow, the plate always enters a complex 3D spinning mode, with significant crosswind motion, which is absent when the plate is aligned at right angles to the flow. This spinning mode is more typical of plates flying in real wind storms.In addition, using a porous region to represent a simple double-eaved building, plates are launched from the roof and their trajectory is simulated. The complex flow fields around the building result in more realistic plate trajectories. For this particular scenario, large suctions on the windward slope of the roof produce large amounts of lift in the plates released from that position, causing them to fly well above the building, never entering the wake of the building
24 May 2016 in Journal of Engineering for Gas Turbines and Power
Thin-film flows encountered in engineering systems such as aero-engine bearing chambers often exhibit capillary waves and occur within a moderate to high Weber number range. Although the depth-averaged simulation of these thin-film flows is computationally efficient relative to traditional volume-of-fluid (VOF) methods, numerical challenges remain particularly for solutions involving capillary waves and in the higher Weber number, low surface tension range. A depth-averaged approximation of the Navier–Stokes equations has been used to explore the effect of surface tension, grid resolution, and inertia on thin-film rimming solution accuracy and numerical stability. In shock and pooling solutions where capillary ripples are present, solution stability, and accuracy are shown to be highly sensitive to surface tension. The common practice in analytical studies of enforcing unphysical low Weber number stability constraints is shown to stabilize the solution by artificially damping capillary oscillations. This approach, however, although providing stable solutions is shown to adversely affect solution accuracy. An alternative grid resolution-based stability criterion is demonstrated and used to obtain numerically stable shock and pooling solutions without recourse to unphysical surface tension values. This allows for the accurate simulation of thin-film flows with capillary waves within the constrained parameter space corresponding to physical material and flow properties. Results obtained using the proposed formulation and solution strategy show good agreement with available experimental data from literature for low Re coating flows and moderate to high Re falling wavy film flows.