8 September 2021 in IEEE Open Journal of the Solid-State Circuits Society
This paper presents challenges and design perspectives for terahertz (THz) integrated circuits and systems. THz means different things to different people. From International Telecommunication Union (ITU) perspective, THz radiation primarily means frequency range from 300 – 3000 GHz. However, recently, a more expansive definition of THz has emerged that covers frequencies from 100 GHz to 10 THz, which includes sub-THz (100 – 300 GHz), ITU-defined THz frequencies. This definition is now commonly used by communication theorists, and since this paper is intended for people with a wide variety of expertise in system and circuit design, we have adopted the latter definition. The paper brings to the open unmitigated shortcomings of conventional transceiver architectures for multi gigabit-per-second wireless applications, unfolds challenges in designing THz transceivers, and provides pathways to address these impediments. Furthermore, it goes through design challenges and candidate solutions for key circuit blocks of a transceiver including front-end amplifiers, local oscillator (LO) circuit and LO distribution network, and antennas intended for frequencies above 100 GHz.
26 August 2019 in IEEE Journal of Solid-State Circuits
A novel high-speed wireless transmitter (TX) architecture is presented that directly transforms incoming data bits into high-order 4M-quadrature amplitude modulation (QAM) constellation by adding multiple quadrature phase shift keying (QPSK) signals with appropriate amplitude ratios. The costly high-speed digital-to-analog converters (DACs) in conventional TXs are thus completely avoided, resulting in a highly integrated solution amenable to ultra-high speeds and operating frequencies. Design tradeoffs are analyzed in detail. Based on this article, a TX prototype at 115-GHz carrier frequency implementing the 16QAM direct-modulation scheme is fabricated in a 180-nm SiGe BiCMOS process (fMAX = 270 GHz). Wireless testing at a 20-cm distance with 25-dBi horn antennas on both transmitting and receiving side measures 20-Gb/s data rate with an error vector magnitude (EVM) of -15.8 dB and modulated output power of +1 dBm. The TX consumes 520 mW of power and occupies 3.17 mm² of active area.
10 September 2021 in IEEE Journal of Solid-State Circuits
This article presents a multipolar neural stimulation and mixed-signal neural data acquisition (DAQ) chipset for fully implantable bi-directional brain–computer interfaces (BD-BCIs). The stimulation system employs four 40 V compliant current-stimulators, each capable of sourcing/sinking a maximum 12.75 mA stimulation current, connected to 16 output channels through a high-voltage (HV) switch fabric. A novel time-based charge balancing (TBCB) technique is introduced to reduce the residual voltage on the electrode-electrolyte interface during the inter-pulse time interval, achieving 2 mV charge balancing precision. Additionally, an analytical study of the charge balancing accuracy for the proposed technique is provided. The recording system incorporates a dual-mode DAQ architecture that consists of a 32-element front-end array and a mixed-signal back-end including analog-to-digital converters (ADCs) for both training (i.e., full-band) and decoding (i.e., baseband) operations. Leveraging the flexibility of the multipolar operation, stimulation-side contour shaping (SSCS) artifact cancellation is adopted to significantly suppress stimulation artifacts by up to 45 dB. SSCS method prevents the recording front-ends from saturation and greatly relaxes the dynamic range requirement of the recording system, enabling a truly bi-directional operation. The prototype chipset is fabricated in an HV 180-nm CMOS process and demonstrates a significant performance improvement compared to the prior art.
24 October 2019 in IEEE Journal of Solid-State Circuits
A CMOS 170-GHz fundamental-frequency transmitter (TX) realizing the 8PSK modulation scheme directly in the RF domain is presented. The use of direct RF modulation obviates the need for high-resolution high-speed mixed-signal blocks. The proposed architecture extends the conventional quadrature modulation by performing additional phase modulation on I and Q components of the LO signal, which helps increase modulation order. The TX employs high-speed switchable phase shifters to achieve LO phase modulation and fundamental-frequency over-neutralized power amplifiers to drive an integrated two-element tapered dipole antenna array. Fabricated in a 65-nm CMOS process ( fT/fmax = 230/260 GHz), the RF-8PSK TX prototype occupies 3.2 × 2.8 mm 2 of die area. The free-space wireless measurement of the TX over a 10-cm link range yields 15 Gb/s data rate at an error vector magnitude (EVM) of -14.8 dB. The TX achieves an EIRP of 4 dBm while consuming 560-mW power.
24 July 2009 in IEEE Journal of Solid-State Circuits
Design and implementation of a millimeter-wave dual-band frequency synthesizer, operating in the 24 GHz and 77 GHz bands, are presented. All circuits except the voltage controlled oscillators are shared between the two bands. A multi-functional injection-locked circuit is used after the oscillators to simplify the reconfiguration of the division ratio inside the phase-locked loop. The 1 mm times 0.8 mm synthesizer chip is fabricated in a 0.18 mum silicon-germanium BiCMOS technology, featuring 0.15 mum emitter-width heterojunction bipolar transistors. Measurements of the prototype demonstrate a locking range of 23.8-26.95 GHz/75.67-78.5 GHz in the 24/77 GHz modes, with a low power consumption of 50/75 mW from a 2.5 V supply. The closed-loop phase noise at 1 MHz offset from the carrier is less than -100 dBc/Hz in both bands. The frequency synthesizer is suitable for integration in direct-conversion transceivers for K/W-band automotive radars and heterodyne receivers for 94 GHz imaging applications.
9 July 2019 in IEEE Journal of Solid-State Circuits
This paper presents the theory, design, and implementation of an 8PSK direct-demodulation receiver based on a novel multi-phase RF-correlation concept. The output of this RF-to-bits receiver architecture is demodulated bits, obviating the need for power-hungry high-speed-resolution data converters. A single-channel 115-135-GHz receiver prototype was fabricated in a 55-nm SiGe BiCMOS process. A max conversion gain of 32 dB and a min noise figure (NF) of 10.3 dB were measured. A data rate of 36 Gb/s was wirelessly measured at 30-cm distance with the received 8PSK signal being directly demodulated on-chip at a bit-error rate (BER) of 1e-6. The measured receiver sensitivity at this BER is -41.28 dBm. The prototype occupies 2.5 x 3.5 mm² of die area, including PADs and test circuits (2.5-mm² active area), and consumes a total dc power of 200.25 mW.