This paper presents the theory, design, and implementation of an 8PSK direct-demodulation receiver based on a novel multi-phase RF-correlation concept. The output of this RF-to-bits receiver architecture is demodulated bits, obviating the need for power-hungry high-speed-resolution data converters. A single-channel 115-135-GHz receiver prototype was fabricated in a 55-nm SiGe BiCMOS process. A max conversion gain of 32 dB and a min noise figure (NF) of 10.3 dB were measured. A data rate of 36 Gb/s was wirelessly measured at 30-cm distance with the received 8PSK signal being directly demodulated on-chip at a bit-error rate (BER) of 1e-6. The measured receiver sensitivity at this BER is -41.28 dBm. The prototype occupies 2.5 x 3.5 mm² of die area, including PADs and test circuits (2.5-mm² active area), and consumes a total dc power of 200.25 mW.
17 December 2021 in IEEE Journal of Solid-State Circuits
In this work, we present a wireless energy-efficient fully integrated amplitude shift keying (ASK) transmitter (TX) array at 220 GHz. Each TX cell consists of an oscillator, a modulation switch, an on-chip antenna, and baseband amplifiers. The oscillator uses a harmonic generation technique that is optimized for maximum output power and efficiency. The ASK scheme is used for data modulation and is implemented with a fast switch that does not consume any dc power. Three of these TX cells are coherently coupled together to increase the signal-to-noise ratio (SNR) and, hence, the data rate. This also enables the possibility of having a four-level spatial ASK modulation. Fabricated in a 55-nm SiGe bipolar complementary metal oxide semiconductor (BiCMOS) process, the array dissipates 165.2 mW of dc power and generates 4.2-dBm effective isotropic radiated power (EIRP). The chip demonstrates a 20-Gb/s data transmission rate with on-off keying (OOK) modulation at a 28-cm distance using low-cost Teflon lenses. The measured energy efficiency of the array is 8.26 pJ/bit. To the best of our knowledge, this work demonstrates the best energy efficiency among TX arrays at this frequency range.
We review the recent advances on the implementation of electronic circuits that operate in the millimeter-wave (30–300 GHz) and terahertz (300–3000 GHz) frequency ranges. The focus of this article is on nonlinear phenomena in electronics. The different implementations of nonlinear circuits for the sake of millimeter-wave and terahertz signal generation are studied in this paper. The challenges of signal generation are examined and the benefits and limitations of different schemes of signal generation are discussed. It is shown that nonlinear devices such as electronic transistors exhibit major advantages enabling realization of low-cost and portable circuits for the emerging applications in these frequency ranges. We also review linear and nonlinear design methodologies employing the properties of electromagnetic waves. The electronic systems designed based on the presented ideas are shown to push the previously unbeatable limits of operation in millimeter-wave and terahertz frequency ranges. A discussion on remaining challenges and future directions concludes the paper.
24 January 2018 in IEEE Solid-State Circuits Letters
An embedded digital temperature sensor based on a single-ended probe is implemented in a 28 nm fully-depleted silicon-on-insulator (FD-SOI) process. The nMOS-only ring-oscillator probe uses single-point calibration based on body-bias tuning of its well for process compensation. Non-linearity compensation is implemented on-chip in custom digital logic, resulting in an area-efficient (225 μm2 per probe, 11482 μm2 for the full system) sensor while achieving -1.4∘C / +1.3∘C accuracy using 2.0 nJ/Sample and maintaining functionality over a 0.62V-1.2V range, making it suitable for temperature monitoring in digital systems-on-chip (SoCs).
This paper presents a 7-parameter analytical model of the MOS transistor based on the inversion charge targeted at the development of simplified analytical circuit design methodologies that take into account the physics of the MOS transistor. The proposed design-oriented model allows for the first time to describe both the main short-channel effects of advanced nanometric technologies and the dependence of the transistor drain current on the drain voltage, while the model remains valid for all bias regimes (from weak to strong inversion) and for all operating regions (linear and saturated). A simple procedure based on the device physics is proposed to estimate the transistor model parameters for a given technology. Furthermore, analytical expressions of the current derivatives are developed targeting different design scenarios. The accuracy of the proposed model is validated by direct comparison to silicon measurements of N-MOS transistors in 28 nm FD-SOI technology for channel width of 1 μm and channel lengths of 30 nm, 60 nm and 150 nm, and also to simulations performed with an industry-standard compact model.
While there exists a wide variety of radio frequency (RF) technologies amenable for usage in Wireless Body Area Networks (WBANs), which have been studied separately before, it is currently still unclear how their performance compares in true on-body scenarios. In this paper, a single reference on-body scenario—that is, propagation along the arm—is used to experimentally compare six distinct RF technologies (between 420 MHz and 2.4 GHz) in terms of path loss. To further quantify on-body path loss, measurements for five different on-body scenarios are presented as well. To compensate for the effect of often large path losses, two mitigation strategies to (dynamically) improve on-body links are introduced and experimentally verified: beam steering using a phased array, and usage of on-body RF repeaters. The results of this study can serve as a tool for WBAN designers to aid in the selection of the right RF frequency and technology for their application.