24 June 2021 in IEEE Antennas and Wireless Propagation Letters
A planar quasi-Yagi antenna with cointegrated filtering functionality and flat in-band gain is reported. It exploits complementary-diplexer-based reflectionless-filtering techniques through the inclusion of an absorptive branch to realize the codesigned filtering functionality. This absorptive branch consists of a second-order bandstop-filter (BSF) unit loaded by a grounded resistor that is connected in parallel with the initial planar quasi-Yagi antenna. By designing the reflection coefficients of the basic antenna and the absorptive branch to be nearly complementary in frequency, the out-of-band RF power not radiated by the antenna is transmitted by the BSF to its loading resistor that dissipates it. In this manner, a quasi-absorptive filtering action is added to the antenna. Moreover, whereas the out-of-band radiation efficiency of the antenna is highly suppressed, its in-band behavior is kept as the in-band RF power is not transmitted by the BSF but radiated by the antenna as usual. For the experimental-validation purposes, a microstrip antenna prototype is developed and measured. Flat in-band gain with a ripple lower than 1 dB within the operational range of the antenna (2.6-3.06 GHz) is obtained as an added merit.
28 February 2018 in IEEE Transactions on Antennas and Propagation
This paper presents the extensive study on the effects of inhomogeneous substrate and superstrate for the exploration of dual-band and dual-circularly polarized patch antenna. As well known to all, the technology for circularly polarized (CP) patch antenna has been often restrictedly achieved by altering the shape of patch conductor surface by a few standard manufacturing processes. Benefited from the 3-D printing technology, it is demonstrated here that CP waves can be alternatively generated via an intact metal patch mounted on low-profile inhomogeneous substrate. As for the inhomogeneous superstrate, low profile is insufficient to make it become a polarizer. As such, a dual-band and dual-CP stacked patch antenna is proposed, where the lower patch and its superstrate exactly serve as the ground and substrate of the upper one. Different impacts of low-profile inhomogeneous substrate and superstrate on polarization are utilized to ensure the isolation of left- and right-hand circular polarizations. Besides, due to the usage of intact patches, two operating bands are independently formed and can be easily located in proximity to each other. A prototype operating at 2.75 and 3.2 GHz is then fabricated and measured. Measured results are found in reasonably a good agreement with the simulated ones.
11 November 2019 in IEEE Transactions on Vehicular Technology
A dual-band dual-circularly polarized (CP) all-metal antenna is proposed in this paper for vehicular communications to realize large signal coverage and high isolation over two bands. On the one hand, by combining two rings of three-dimensional (3-D) L-shaped stubs and a circular patch, opposite CP radiations, i.e., right-hand circular polarization (RHCP) and left-hand circular polarization (LHCP), can be achieved in lower and higher working frequency bands respectively, thus ensuring the isolation between different channels. On the other hand, both radiation patterns of two bands are conical-beam, i.e., omnidirectional, so as to realize large signal coverage, which is beneficial for vehicular communication especially when the car is moving or located on nonplanar plane. Besides, the proposed antenna is all-metal and can be easily manufactured by computer numerical control (CNC) machining technology. As such, it is expected to have higher power capacity than the conventional printed circuit board (PCB) structure. A prototype operating at 2.6 and 2.98 GHz is fabricated and measured, indicating that small frequency ratio between two operating bands can be realized. The proposed antenna is promisingly useful for application on vehicle to ensure simultaneous communications between different links without crosstalk, such as vehicle-to-satellite and vehicle-to-basestation communications.
29 June 2020 in IEEE Antennas and Wireless Propagation Letters
A circularly polarized (CP) filtering patch antenna implemented via dispersive delay line (DDL) is proposed in this letter by adopting a new strategy of polarization isolation. Different from linearly polarized antenna, the effective radiation gain of a CP antenna, i.e., CP gain, is not only determined by the magnitude of electric field but also its phase. For a CP antenna, left-hand circular polarization has perfect isolation with the right-hand one, which has nothing with the orientation between transmitters and receivers. As such, the aforementioned concept is specially used in the proposed design of CP filtering antenna and achieved by DDL, which works as a key technique in the proposed antenna. By controlling the parameters of DDL, the in-band and out-of-band phases of two orthogonal electric components are effectively changed, thus affecting the axial ratio, and finally leading to opposite CP radiations of in-band and out-of-band, which means that filtering performance has been realized. For demonstration, an antenna prototype operating at 2.4 GHz is fabricated and measured. The simulated and measured results match well with each other. More importantly, the feasibility of proposed CP filtering strategy is verified by the good filtering performance of CP radiation gain.
29 September 2017 in IEEE Transactions on Antennas and Propagation
This communication proposes a frequency-reconfigurable patch antenna using low-loss transformer oil ( $\varepsilon _{\mathbf {r}} = 2.2$ ), which is a kind of high-frequency liquid. A two-layer substrate is introduced between the patch and ground plane. The upper one is made of homogeneous polytetrafluoroethylene ( $\varepsilon _{r} = 2.2$ ) substrate, while the lower layer consists of a transparent container, including air and transformer oil layers. By varying the height of transformer oil layer, the volume ratio of air to liquid is changed as a function of this height. As such, the effective permittivity of the entire substrate underneath the patch can be tuned so as to realize the so-called frequency reconfiguration. After extensive analysis is carried out, a prototype of the proposed antenna is fabricated and measured. Measured results are found in reasonably good agreement with the simulated ones. A wide tunable impedance bandwidth of 32% from 1.42 to 1.96 GHz is achieved. Moreover, the prototype shows high radiation efficiency because of the low-loss transformer oil.
27 December 2019 in IEEE Antennas and Wireless Propagation Letters
This letter proposes a dielectric helical antenna made of 3-D printed zirconia ceramic, which possesses better performance than the conventional metal one. On the one hand, the radiation principle of proposed antenna is investigated by regarding its structure as a dielectric waveguide. It is found that a dielectric waveguide operating at cut-off state of higher mode, here is TM01 mode, can radiate electromagnetic (EM) waves. The propagation constant of EM waves in waveguide is extracted to demonstrate that the dielectric waveguide indeed works as a fast-wave status at this moment. On the other hand, both the far-field and scattering performances between proposed and conventional helical antennas are comparatively studied. It is observed that the structure composed of dielectric helix and metal ground can achieve similar radiation gain, axial ratio (AR) and AR bandwidth as the conventional all-metal helical antenna, but possessing lower radar cross section (RCS) at high frequency. Benefited from ceramic stereolithography apparatus (CSLA), the proposed structure can be fabricated precisely, and measured results have reasonably validated the simulated ones.