A type of compact single/multi-band coupled-multi-line filtering section and its application to the design of RF filtering devices are presented. This one-port filtering cell is made up of N+1 intercoupled quarter-wavelength transmission-line segments for the generation of a transfer function with a total of N+1 transmission zeros (TZs) distributed at both sides of all its N first-order passbands when arranged in the transmission mode. Design formulas for the produced poles and TZs of its corresponding normalized coupling-routing diagram and illustrative theoretical responses are provided. Furthermore, for experimental demonstration purposes, microstrip prototypes of the following RF filtering components that exploit the conceived filtering section are manufactured and measured: 1) a quasi-elliptic-type diplexer with a dual-band bandpass filter (BPF) junction; 2) two input-reflectionless triple-band BPF and bandstop filter (BSF) circuits; and 3) an out-of-phase equal-power-division bandpass filtering coupler with input-quasi-reflectionless behavior.
15 March 2017 in IEEE Transactions on Microwave Theory and Techniques
This paper first presents two types of wideband microstrip-to-microstrip equal ripple vertical transitions designed with the uniform and folded slotline structures, respectively. By solving the characteristic function with differential calculation, the condition for realizing the constant equal ripple frequency response but different bandwidths (BWs) for the proposed transition is determined with resorting to the characteristic impedances of the coupled open-circuited microstrip line and slotline. Then, a vertical transition with the uniform slotline is synthetically analyzed and designed with Chebyshev polynomial function and another similar vertical transition with the same in-band ripple level but different BWs is also comparatively presented. By modifying the normalized impedances of the proposed transition to make the theoretical result close to the simulated one with the initial normalized impedances, the transformer turns ratios of the microstrip-to-slotline intersection is exactly calculated by the impedance ratios between two corresponding sets of normalized impedances. Due to the degraded high-frequency performance caused by the radiation loss of the uniform slotline, two vertical transitions with the folded slotline structure are further analyzed and the related turn ratios are extracted with the proposed approach. To verify the effectiveness on the reduction of radiation loss for the folded slotline structure, a six-pole wideband bandpass filter is presented with high-frequency performance greatly improved. In final, wideband vertical transitions with different slotline structures and a six-pole wideband bandpass filter are synthetically designed, simulated, fabricated, and measured.
24 June 2021 in IEEE Antennas and Wireless Propagation Letters
A planar quasi-Yagi antenna with cointegrated filtering functionality and flat in-band gain is reported. It exploits complementary-diplexer-based reflectionless-filtering techniques through the inclusion of an absorptive branch to realize the codesigned filtering functionality. This absorptive branch consists of a second-order bandstop-filter (BSF) unit loaded by a grounded resistor that is connected in parallel with the initial planar quasi-Yagi antenna. By designing the reflection coefficients of the basic antenna and the absorptive branch to be nearly complementary in frequency, the out-of-band RF power not radiated by the antenna is transmitted by the BSF to its loading resistor that dissipates it. In this manner, a quasi-absorptive filtering action is added to the antenna. Moreover, whereas the out-of-band radiation efficiency of the antenna is highly suppressed, its in-band behavior is kept as the in-band RF power is not transmitted by the BSF but radiated by the antenna as usual. For the experimental-validation purposes, a microstrip antenna prototype is developed and measured. Flat in-band gain with a ripple lower than 1 dB within the operational range of the antenna (2.6-3.06 GHz) is obtained as an added merit.
8 December 2020 in IEEE Transactions on Microwave Theory and Techniques
An approach to design RF all-port-reflectionless quasi-elliptic-type single-/dual-band bandpass filters (BPFs) and diplexers with frequency-adaptive constant-absolute-bandwidth (ABW) response is reported. The tunable reflectionless BPF case is first addressed, where a balanced-circuit scheme composed of two identical wideband 3-dB quadrature couplers and two equal reflective-type BPF units with synchronous center-frequency agility is exploited. The input signal is split into the two BPF units with equal amplitude and 90°; phase shift by the first coupler and then recombined at the output node of the second coupler after being processed by the balanced-circuit branches. In this manner, the signals reflected at the stopband regions of the BPF units are mutually canceled at the coupler input port and absorbed at the isolated port by its loading resistor. This allows a symmetrical low-reflection behavior to be attained in the overall circuit, whose filtering transfer function is the one determined by the BPF units. Furthermore, by using dual-band BPFs in the balanced-circuit branches, this concept is readily extended to frequency-tunable constant-ABW dual-band BPFs whose passbands can be separately switched OFF (i.e., absorptive switched-OFF states) as an added reconfiguration capability. For practical-demonstration purposes, starting from theoretical design guidelines followed by an optimization step, the third- and second-order microstrip prototypes of reflectionless frequency-controllable single- and dual-band BPFs with predefined constant ABW, respectively, are developed and tested. Afterward, inspired by the devised tunable absorptive BPF structure, an all-port-reflectionless diplexer with frequency-adjustable constant-ABW channels is shown. This controllable multiport-absorptive filtering device is also verified with the fabrication and testing of a microstrip prototype. All the constructed circuits employ varactor diodes for electronic tuning, showing close agreement between simulation and measurements.
6 September 2023 in IEEE Transactions on Microwave Theory and Techniques
An approach for the realization of radiofrequency (RF)/microwave balanced filters with simultaneous differential-mode (DM) and common-mode (CM) two-port-reflectionless behavior for bandpass, quasi-bandstop, and dual-passband applications is reported. These RF filtering components exploit as basic constituent circuit block a type of two-layer broadband magic-T, in which its two-side $/$ coplanar arms are designed as the balanced feeding ports at the top layer. Specifically, two replicas of this wideband magic-T on a microstrip-to-slotline transition are back-to-back connected between their $\bm{\Delta}$ terminals by means of a double-complementary-diplexer-based single-ended low-reflection filtering unit inserted at the bottom layer. In addition, their $\bm{\Sigma}$ accesses are loaded with a resistor to perform the CM RF-power-absorption functionality. Thus, balanced symmetrical-absorptive RF filtering devices for both the DM and CM operations are developed. Such distinctive feature makes this family of microwave filters unique since most of related prior-art balanced filters mainly focused on obtaining the RF-power-absorption property only for the DM or the CM. The theoretical operational foundations and RF design principles of the engineered class of balanced filters with double DM and CM symmetrical-absorptive capabilities are described. Furthermore, their two-layer implementations exemplified in second-and fourth-order bandpass filters (BPFs), a second-order quasi-bandstop filter (BSF), and a second-order dual-band BPF are presented. For experimental-validation purposes, three different prototypes centered around 2 GHz corresponding to single-band BPF and quasi-BSF devices, as well as a dual-band BPF circuit with passbands located at 1.75 and 2.25 GHz, are manufactured and tested. For all these prototypes, 10-dB-referred DM and CM two-port-RF-power-absorption relative spectral ranges larger than 3:1 are measured. Their expected RF filtering functionalities and highly suppressed CM transmission at all frequencies are also verified.
A millimeter-wave passive-integrated bandstop filter (BSF) with absorptive/reflectionless behavior is reported. It avoids the creation of RF-power reflections for filtered signals which can deteriorate earlier active stages in integrated RF front-end chains. It exploits a two-path transversal configuration in a multi-layer structure. Specifically, it is composed of a direct transmission line for the main path (top layer) and two lossy edge-grounded spiral-shaped resonators for the secondary path (bottom layer) that are coupled between them and to the main path. Thus, a sharp second-order stopband is created through destructive signal-interference effects between the two signal paths with intrinsic RF-power absorption within the volume of the lossy resonators. As practical validation, a 24.5-GHz on-chip millimeter-wave absorptive BSF circuit is built in a 0.13-μm SiGe bipolar complementary metal-oxide-semiconductor [(Bi)-CMOS] technology and tested. Close agreement between simulated and measured results for this on-chip BSF circuit is achieved.