Haptic gloves allow the players to feel the virtual world more realistically by providing force feedback. At present, haptic gloves are mainly driven by conventional motors, and for them, being lightweight, low cost, low in power consumption, and intrinsically safe to operators are challenging. Here, we designed a haptic glove (So-EAGlove) integrating a flexible electrostatic adhesive brake to resist human fingers with a tunable braking force and render a softness sensation. This glove weighs only 51 g, but is capable of simulating objects in a large range of Young's modulus from 540 Pa to 5.4 MPa. The electrostatic adhesive brake costs only approximately 2.43 mW during operation, i.e., more than three days powered by a small button battery. We built a feedforward control model and evaluated its performance. Experimental results show that this glove can generate an accurate force to follow the force-displacement profile of the corresponding real objects. The error is less than 7%, barely noticeable by the subjects. The subjective tests also demonstrate that little statistical difference exists between the real objects and the virtual objects for the subjects.
Miniature locomotion robots with the ability to navigate confined environments show great promise for a wide range of tasks, including search and rescue operations. Soft miniature locomotion robots, as a burgeoning field, have attracted significant research interest due to their exceptional terrain adaptability and safety features. Here, a fully‐soft centimeter‐scale miniature crawling robot directly powered by fluid kinetic energy generated by an electrohydraulic actuator is introduced. Through optimization of the operating voltage and design parameters, the average crawling velocity of the robot is dramatically enhanced, reaching 16 mm s−1. The optimized robot weighs 6.3 g and measures 5 cm in length, 5 cm in width, and 6 mm in height. By combining two robots in parallel, the robot can achieve a turning rate of ≈3° s−1. Additionally, by reconfiguring the distribution of electrodes in the electrohydraulic actuator, the robot can achieve 2 degrees‐of‐freedom translational motion, improving its maneuverability in narrow spaces. Finally, the use of a soft water‐proof skin is demonstrated for underwater locomotion and actuation. In comparison with other soft miniature crawling robots, this robot with full softness can achieve relatively high crawling velocity as well as increased robustness and recovery.
Recent advances in soft robotics demonstrate the requirement of modular actuation to enable the rapid replacement of actuators for maintenance and functionality extension. There remain challenges to designing soft actuators capable of different motions with a consistent appearance for simplifying fabrication and modular connection. Origami structures reshaping along with their unique creases became a powerful tool to provide compact constraint layers for soft pneumatic actuators. Inspired by Waterbomb and Kresling origami, this article presents three types of vacuum-driven soft actuators with a cubic shape and different origami skins, featuring contraction, bending, and twisting-contraction combined motions, respectively. In addition, these modular actuators with diversified motion patterns can be directly fabricated by molding silicone shell and constraint layers together. Actuators with different geometrical parameters are characterized to optimize the structure and maximize output properties after establishing a theoretical model to predict the deformation. Owing to the shape consistency, our actuators can be further modularized to achieve modular actuation via mortise and tenon-based structures, promoting the possibility and efficiency of module connection for versatile tasks. Eventually, several types of modular soft robots are created to achieve fragile object manipulation and locomotion in various environments to show their potential applications.
This research presents a new class of versatile multi‐material hybrid actuators (MASH actuators), powered by pneumatics and electrostatic adhesion (EA)‐based adaptive strain‐limiting layers. Soft pneumatic actuators with strain‐limiting layers as the mainstream actuation for soft robotics have been developed for decades. However, due to their permanent strain‐limiting layers, those actuators possess fewer motion patterns. Inspired by the longitudinal muscles of the earthworm, a concept of an adaptive strain‐limiting layer with the ability to vary its length, stiffness, and position is presented. By integrating two flexible EA brakes into a soft pneumatic actuator as adaptive strain‐limiting layers, the actuator can achieve multiple motion patterns including extension, contraction, and bilateral bending, with permutations among these motions. The EA‐based strain‐limiting layer can increase the original actuator length by up to 86%, and the baseline actuator stiffness by up to 605%. To demonstrate its potential in locomotion and manipulation, an earthworm‐inspired crawling robot possessing great terrain adaptability and a versatile soft robotic gripper based on this hybrid actuator concept are developed.
The field of soft manipulators requires a more promising solution, including efficient structures and controllers. This paper presents a novel cable–pneumatic hybrid-driven tapered soft manipulator (TSM) design and control scheme to enhance the performance in actual tasks. This paper is the first to present the design with a Bowden tube as a driving tendon and propose a composite tendon with Bowden tubes and cable tendons (BTCTs). Leveraging the principles of hybrid-driven antagonism, the compact TSM integrates the composite tendon with BTCTs and pneumatically actuated tapered bellows (PATBs). This new hybrid-driven form provides the TSM with excellent resistance to axial extension, tangential bending, and torsion, enhancing the stiffness of the TSM. The variable-stiffness range of the TSM was quantified in tests including axial stiffness (0.57–10.77 N/mm), tangential bending stiffness (0.01–0.45 N/mm), and torsion stiffness (0.02–0.044 Nm/deg) tests. A deep learning-based neural network (NN) approach was utilized to model the inverse kinematics of the TSM. For more precise motion control, using position and orientation feedback from the sensor at the tip, we have designed a closed-loop iterative feedback controller (IFC) incorporating three algorithms. Experiments on spatial point positioning, trajectory tracking with different constraints, orientation control, and disturbance experiments were conducted on the TSM. Experimental results (spatial point positioning error (mean error of stable region: 0.17 mm), circular trajectory tracking error (mean and standard deviation of 100 trials: 0.87 $\pm$ 0.57 mm), orientation control error (less than 1 $^{\circ }$ ), and the performance in disturbance experiment) demonstrated that our approach has high control accuracy and strong robustness against external disturbances. We conducted experiments involving teleoperation control, collision-free precise operations in cluttered and constrained environments, and disturbance-adaptive board cleaning testing, ensuring both stability and safety during contact with humans. These experiments intuitively demonstrate the potential of this TSM for executing complex tasks in real-world environments, promising to become a safe collaborative assistant for humans in the future.
3 December 2024 in IEEE/ASME Transactions on Mechatronics
Soft electrohydraulic actuators, also known as hydraulically amplified self-healing electrostatic (HASEL) actuators have attracted widespread research interest due to their outstanding dynamic performance and high output power. However, the displacement of electrohydraulic actuators usually declines with time with a constant dc voltage, which hampers its prospective application. In this article, a systematic model is first established to not only explain the inconsistent behaviors in the displacement of electrohydraulic actuators with dc voltage but also predict the relatively stable displacement with oscillation with ac square wave voltage, with further experimental validation. To smooth the displacement oscillation introduced by ac voltage, a serial elastic component is incorporated to form a series elastic HASEL (SE -HASEL) actuator. A feedback control with a proportion-integration algorithm enables the SE-HASEL actuator to eliminate the obstinate displacement hysteresis. The results revealed that, through the proposed methodology, the SE-HASEL actuator can simultaneously provide stable and smooth displacement. Furthermore, to demonstrate the potential applications, this article also proposes a highly accurate needle biopsy robot and a rotary robotic joint based on the SE-HASEL actuator. Overall, this study has achieved ac voltage-driven series elastic electrohydraulic actuators that can output stable and smooth displacement.