Composite phase change materials consisting of a high-latent-heat phase change material (PCM) embedded in a high-thermal-conductivity matrix are desirable for thermally buffering pulsed heat loads via rapid absorption and release of thermal energy at a constant temperature. This paper reports a composite PCM thermal buffer consisting of a Field's metal PCM having high volumetric latent heat (315 MJ/m3) embedded in a copper (Cu) matrix having high intrinsic thermal conductivity [384 W/(m·K)]. We demonstrate thermal buffer samples fabricated with Cu volume fractions from 0.05 to 0.2 and sample thicknesses ranging between 1 mm and 4 mm. Experiments coupled with finite element method simulations were used to determine the figures of merit (FOMs), cooling capacity ηeff, energy density Eeff, effective thermal conductivity keff, and the buffering time constant τ. The cooling capacity was measured to be as high as ηeff = 72 ± 4 kJ/(m2·K1/2·s1/2) for the 1.45 mm thick thermal buffer sample having a Cu volume fraction of 0.13, significantly higher than theoretical values for aluminum–paraffin composites [45 kJ/(m2·K1/2·s1/2)] or pure paraffin wax [8 kJ/(m2·K1/2·s1/2)]. Our work develops design guidelines for high-FOM thermal buffer devices for pulsed heat load thermal management.
2 November 2023 in ACS Applied Electronic Materials
Sulfide-based Li superionic conductors are being considered good solid electrolytes for all-solid-state batteries. Despite some benefits of conventional solid-state methods, the end goal of the synthesis of sulfide electrolytes is the development of new liquid-phase methods. Herein, we demonstrate the rational design of a one-pot solvent-assisted route for the simple, facile, and low-cost synthesis of the Sn-substituted Li argyrodite superionic conductors. Our method enables the successful incorporation of Sn into the host lattices, yielding highly crystalline materials with high ionic conductivity (∼2 mS cm−1), good air stability (20% humidity), and excellent Li metal compatibility (1500 h stability). Benefitting from these, at 0.1C, the full cell based on Li6.125P0.875Sn0.125S5Br exhibits an initial discharge capacity of 151 mA h g−1 and ∼66% capacity retention after 50 cycles (99 mA h g−1). This work presents an unprecedented solvent-engineered approach for the fabrication of versatile Li argyrodites substituted with aliovalent cations.
1 April 2017 in Biochimica et Biophysica Acta (BBA) - Gene Regulatory Mechanisms
Achieving a high storage capability while maintaining good rate performance using symmetric microsupercapacitors (MSCs) remains challenging. Herein, a 3D symmetric MSC based on interdigitated 3D bicontinuous pseudocapacitive electrodes is proposed to simultaneously attain ultrahigh energy density and ultrafast response. The 3D electrodes comprise electrolytically active MnO2 layers conformally coated onto a 3D periodic porous Ni current collector. In this architecture, the low conductivity of MnO2 can be compensated by efficient charge transport and facile charge transfer without compromising its high capacitance. The 3D MSC with a 1‐V window exhibits an ultrahigh volumetric energy density of 15.8 mWh cm−3 with a high power density of 4.95 W cm−3, outperforming all previously reported MnO2‐based symmetric MSCs. Benefitting from its ultrafast response, the 3D MSC exhibits superiority in terms of the phase angle (−66°), areal capacitance (1400 µF cm−2), and time constant (0.6 ms) at an alternating‐current (AC) frequency of 120 Hz. By using the 3D MSC as a line‐filtering capacitor in a real circuit, the AC signal is effectively smoothed with small residual ripples (≈1.35 mV). Additionally, the device achieves excellent performance in an all‐solid‐state form.