24 June 2021 in IEEE Transactions on Magnetics
The nanocrystalline alloys are gradually used as shielding materials in wireless power transfer (WPT) systems with the development of high power density. In this article, the system properties of WPT using ferrite and four types of nanocrystalline cores are simulated by 3-D finite element analysis (FEA). Based on this, a novel shielding pad composed of nanocrystalline alloy and ferrite is designed to improve the WPT system properties. The WPT systems are preliminarily compared with 3-D FEA when the different nanocrystalline alloys are used in the novel shielding pad. The experimental WPT system for 85 kHz and 1.5 kW with a 24 cm air gap between the primary and secondary coils is built to validate the simulation. The results show that significantly greater shielding can be realized for the novel pad at the price of a slight decrease of transmission efficiency than conventional ferrite core.
28 February 2020 in IEEE Transactions on Applied Superconductivity
Temperature is a key influence factor of magnetic material properties. It can determine the overall performance of electrical equipment. Accurate measurements of magnetic properties in cores are a prerequisite for loss assessment. In this paper, a testing system for ring sample is designed and constructed to investigate the temperature dependency of magnetic materials, especially at high frequency. Magnetic properties and loss characteristics of the ferrite (N87), nanocrystalline (1k107B) and amorphous alloys (1k101) are measured and analyzed in the range of 25 °C to 120 °C from 1 kHz to 20 kHz. The temperature dependency of three materials at different conditions is systematically compared by using the coefficient of loss variation (CLV). The comprehensive performance of core materials is discussed in combination with the experimental phenomena and results.
24 June 2021 in IEEE Transactions on Magnetics
Soft magnetic powder cores are attractive because of their loss at medium frequency. However, the performance of electrical equipment is affected by temperature increase by the heat of core losses. In this article, the magnetic properties of nanocrystalline powder core, amorphous powder core, X-Flux (Fe-Si), Sendust (Fe-Si-Al), and ferrite are measured and compared in the range of 25 °C–125 °C from 20 to 100 kHz. The discussed magnetic properties include the temperature-dependent coercive field, initial permeability, inductance factor, saturation flux density, and core loss. The results show that magnetic properties depend on temperature and frequency. In comparison, the nanocrystalline powder core has the best temperature stability and relatively low core loss among the five materials, so it can be well used at broad temperature and medium frequency.
23 June 2023 in IEEE Transactions on Power Electronics
In medium-frequency applications, magnetic components generally operate in high-temperature conditions caused by higher power loss and more difficult heat dissipation, which results in changes in their electromagnetic characteristics. In this article, the application-oriented characterization of the typical core materials, Mn-Zn ferrite and Fe-based nanocrystalline alloy, is comprehensively studied. The magnetic parameters under sinusoidal (5–50 kHz) and square (10 kHz) excitation from 20 °C to 125 °C are analyzed detailedly. Combined with the micromagnetic theory, the influence factors of electromagnetic parameters such as permeability and power factor angle are investigated. The loss variation of ferrite with temperature, flux density, and frequency is explained by using the energy loss ratio. The proportion of P h and P dy in total loss with temperature and frequency is compared, and the loss fluctuation of nanocrystalline alloys and ferrite is analyzed. Moreover, the reasonable range of frequency that needs to consider temperature effect in practical applications is suggested. The difference between the B - H loop bias under asymmetrical square excitation and dc bias conditions is compared and illuminated. The effectiveness and limitation of typical Steinmetz equations considering the temperature and duty cycle effect are analyzed, and the suggestion of loss calculation is given combined with the material characteristics.
18 November 2021 in IEEE Transactions on Instrumentation and Measurement
Single-sheet testers (SSTs) with asymmetrical yokes were developed for convenient measurement of 1-D and 2-D magnetic properties of Fe-Si sheets. An inherent drawback of such SSTs is that the magnetic properties in the central region of the specimen are affected by the planar eddy currents induced in the specimen plane facing the pole faces of the yokes, where the magnetic flux enters the specimen in the normal direction. Most relevant studies reported in the literature use large symmetrical double yokes to mitigate the influence of planar eddy currents on the magnetic properties. However, such configuration significantly increases the system complexity. This article proposes a compact cross-yoke SST with the novel arm-slotted specimen and the integrated 2-D B-H sensor to minimize the influence of the planar eddy currents and simplify the structure of the SST. The magnetic properties of non-oriented (NO) Fe-Si sheets of 50JN470 under 1-D and 2-D magnetizations are measured and analyzed. The experimental results from the proposed cross-yoke SST show the agreement with those measured by using the international standard SST.