15 July 2024 in IEEE Transactions on Magnetics
With the widespread use of high-power high-frequency transformers in flexible DC transmission, high-power density motor drive control, and high-power charging fields, the vibration and noise of high-frequency transformer has been drawing more and more attentions from the industry. The nanocrystalline materials is commonly used in the core structure of high-frequency transformers. Although it is generally believed that the magnetostriction of nanocrystalline materials is extremely low, the vibration nois e is still very obvious for the nanocrystalline cores. Therefore, it is necessary to study the vibration and noise characteristics of nanocrystalline cores, especially under the excitation of square or rectangular excitation. This paper constructs a non-sinusoidal measurement system, and the vibration and noise characteristics of rectangle nanocrystalline core under sinusoidal and non-sinusoidal excitations up to 5k Hz are measured. Meanwhile, the effect of zero level times on vibration characteristics is also studied.
1 February 2021 in AIP Advances
The cutting process of silicon steels is a necessary manufacturing technique in electrical equipment. Different cutting methods have different effects on the internal structure and magnetic properties of the electrical steel sheets. Laser cutting can produce thermal stress during processing, while mechanical cutting may cause plastic deformation near the cutting edge, which both lead to deterioration in the magnetic properties of the material. Therefore, studying the effect of different cutting techniques on magnetic properties is of great significance to accurately predict the iron losses of electrical equipment. In this paper, a mobile B-H sensing structure is designed to sense the distribution of local magnetic properties near the cutting edges. Magnetic properties of the non-oriented (NO) silicon steel samples B35A270 and 50JN470 are measured and characterized with the variation of distance from cutting edges. The results demonstrate that the deterioration of magnetic properties depends on the cutting methods and the material characteristics. Wire cutting has little effect on magnetic performance and the effect can be observed near the cutting edge. As a contrast, the decrease of the relative magnetic permeability can be observed in a deeper width of the steel strips cutting by laser. Moreover, the multiple trends of laser cutting loss which vary with cutting depth are compared and discussed. This research can provide a reference for the application of electrical equipment under actual working conditions.
18 November 2021 in IEEE Transactions on Instrumentation and Measurement
Single-sheet testers (SSTs) with asymmetrical yokes were developed for convenient measurement of 1-D and 2-D magnetic properties of Fe-Si sheets. An inherent drawback of such SSTs is that the magnetic properties in the central region of the specimen are affected by the planar eddy currents induced in the specimen plane facing the pole faces of the yokes, where the magnetic flux enters the specimen in the normal direction. Most relevant studies reported in the literature use large symmetrical double yokes to mitigate the influence of planar eddy currents on the magnetic properties. However, such configuration significantly increases the system complexity. This article proposes a compact cross-yoke SST with the novel arm-slotted specimen and the integrated 2-D B-H sensor to minimize the influence of the planar eddy currents and simplify the structure of the SST. The magnetic properties of non-oriented (NO) Fe-Si sheets of 50JN470 under 1-D and 2-D magnetizations are measured and analyzed. The experimental results from the proposed cross-yoke SST show the agreement with those measured by using the international standard SST.
1 February 2023 in AIP Advances
Ultra-thin grain-oriented electrical steel (GOES) with thickness less than 0.1 mm can be used to make the iron core of the reactor and high-power magnetic amplifiers. The design of these electromagnetic devices often relies on the data of magnetic characteristics measured under standard sinusoidal excitation. However, the influence of working conditions such as stress and temperature are ignored. The magnetic properties of the magnetic materials under stress are quite different from those under sinusoidal excitation. It is very important to accurately measure the magnetic properties of ultra-thin GOES under stress conditions. This article presents and analyzes the extensive experimental results of magnetic properties in the rolling direction with uniaxial and biaxial tensile stress applied by piezoelectric materials.
15 September 2023 in Journal of Magnetism and Magnetic Materials
23 February 2023 in Journal of Magnetism and Magnetic Materials