3 May 2025 in Nature Communications
The health inspection of widespread high-speed railway network is crucial to maintain the regular transportation, particularly as the velocity of high-speed trains continues to escalate. To narrow the long inspection period of current track recording vehicle method, we have implemented a laser interferometer sensing system to turn those existing fiber cables within high-speed railway cable ducts into effective sensing elements. Based on the distributed vibration sensing of daily passing trains, an average power spectrum density indicator is used to assess the health of high-speed railway infrastructures. During the observation over one year, average power spectrum densities of 4 typical infrastructures remain stable, indicating their robust health despite challenging environmental conditions. To demonstrate the sensitivity of average power spectrum density indicator on railway faults, we analyze the sensing results of a rail section before and after track maintenance, which shows distinctive average power spectrum density features corresponding to different levels of creep deformation. Additionally, the sensing system can also report other ambient vibrations, such as seismic waves after propagation of over 300 km. It demonstrates the fiber sensing system not only has the ability to act as a real-time supplementary tool for high-speed railway health inspection, but also has potential to establish a large sensing network.
1 August 2023 in IEEE Transactions on Instrumentation and Measurement
Over the past few decades, fiber-optic time synchronization (FOTS) has provided fundamental support for the efficient operation of modern society. Due to the finiteness of the speed of light, calculating the fiber link delay is a key step in the traditional FOTS methods to achieve time synchronization. In this paper, a time reversal enabled FOTS method is proposed. Enabled by time reversal, a new idea for FOTS is demonstrated: the clock difference between two sites can be measured without calculating the fiber link delay. Therefore, the data layer is no longer needed to exchange the timing information between two sites. It can also achieve multiple-access time synchronization along the fiber link. Time synchronization performance characterized by time deviation (TDEV) of 25 ps at 1 s and 2 ps at 1000 s on a 230 km fiber link are obtained, and the function of multiple access is demonstrated.
26 June 2024 in Journal of Lightwave Technology
Phase is of great significance in many fields, which can be used to carry important information. In a fiber optic sensing system, phase is crucial for extracting environment information along fiber link. Therefore, the accuracy of the phase resolving result significantly influences the performance of a fiber optic sensing system. There are some widely used phase demodulation method like 3 × 3 coupler demodulation method, in-phase quadrature (IQ) demodulation method and phase generated carrier (PGC) demodulation method, which usually have an imbalance error or distortion problem. In this paper, a novel phase resolving method is proposed and used in an interferometric fiber optic sensing system. Comparison between proposed method and commercial IQ demodulator is carried out. The proposed method is proved to have a better orthogonality performance. Furthermore, the proposed method has less bandwidth limits compared with a digital IQ demodulation method, giving it a broader application.
25 March 2024 in IEEE Transactions on Instrumentation and Measurement
In recent years, fiber-based frequency dissemination has attracted widespread attention. A phase-locked loop (PLL) on the transmitter side (TX) is used to compensate for the phase noise caused by the environmental disturbance (PNE). However, the phase noise caused by transfer delay (PNT) cannot be suppressed. A clean PLL on the receiver side (RX) is used to improve the phase noise of the received signal. Consequently, the performance of PLLs on both sides significantly impacts the phase noise of the final recovered signal. Empirical configurations of PLL parameters often fail to achieve optimal results. In this paper, a phase noise control method is proposed and demonstrated. Through analyzing the PNT, PNE, and phase noise margin of the recovered signal, we optimally configure the PLL parameters at the TX and RX. In this way, the PNT is effectively suppressed and the compensation capability for the PNE is evaluated. By comparing the anthropogenic noise in different environments and the compensation capability of the system, this analysis can provide a reference for the construction of large-scale time-frequency networks.
14 June 2024 in IEEE Transactions on Instrumentation and Measurement
Fiber optic networks are used worldwide and have been regarded as excellent media for transmitting time-frequency (TF) signals. In the past decades, fiber-based TF synchronization techniques have been extensively studied. Instruments based on these techniques have been successfully applied. With the increasing application of TF synchronization instruments, their security has become an important issue. Unfortunately, the security risks of fiber-based frequency synchronization (FbFS) instruments have been overlooked. This paper proposes a frequency tampering method called “frequency expander”. On a 200 km fiber link, we demonstrate a frequency tampering scenario using a frequency expander-enabled frequency tampering module (FTM). On the user side, the frequency value of the recovered 100 MHz signal can be stealthily altered within a range of 100 MHz±100 Hz, while the frequency dissemination stability of the system remains normal. Related to this tampering risk, potential hazards in two different application scenarios, which rely on precise frequency references, are analyzed. Two countermeasures are also proposed to solve this tampering risk.
8 November 2025 in Laser & Photonics Reviews
With the continuous advancement of laser technology, accurately evaluating the noise spectrum of high‐performance lasers has become increasingly challenging. In this work, we demonstrate a high‐precision laser spectrum analyzer based on the proposed digital decoherence method, which can precisely measure the frequency noise spectrum of sub‐Hz linewidth lasers. In addition, it has broad wavelength compatibility, which enables convenient switching between lasers with different center wavelengths. Its performance is validated through measurements of ultra‐stable lasers. Based on the measured frequency noise power spectral density, a β‐line linewidth is determined to be 570 mHz at a 10‐s observation time, and the minimum observable linewidth is calculated to be 133 mHz. The system's noise floor is evaluated to be 210 mHz β‐line linewidth at a 25‐s observation time, and the minimum observable linewidth is 39 mHz.