Aluminum nitride (AlN), a versatile ceramic with high thermal conductivity, high electrical resistivity, and a coefficient of thermal expansion compatible with silicon, is well‐suited for direct‐to‐chip cooling applications of electronics, implementation in wide bandgap semiconductors, and for high‐temperature heat exchangers. Despite multiple advantages, AlN's implementation in liquid‐cooling applications is often hindered by surface‐degrading effects of working‐fluid‐induced hydrolysis. Herein, a scalable ‐but highly tunable‐ wettability engineering approach is introduced, that allows effective implementation of bulk AlN substrates in enhanced two‐phase cooling of electronics. The approach prevents hydrolysis of AlN by aqueous media and establishes control over surface roughness, all the while maintaining bulk integrity and material properties of the underlying substrate. Demonstration of the new approach is presented in spontaneous, pumpless, surface liquid transport, a necessity if such ceramics are to play an integral role as components of sealed, phase‐change, wickless thermal‐management devices (e.g., vapor chambers or heat pipes) that require rapid working‐fluid transport in their multi‐phase interior. The novelty of this work lies in establishing a scalable methodology for utilizing and further enhancing the properties of this non‐oxide ceramic material for phase‐change heat‐transfer hermetic devices, thereby paving the way toward the implementation of this intriguing material in next‐generation heat spreaders.
High‐power‐density modern electronics necessitate efficient and reliable heat removal at heat fluxes exceeding 1 kW cm −2 , a demand that challenges the limits of conventional cooling strategies. The precise functionalization of surfaces is pivotal in developing advanced thermal management solutions for next‐gen electronics cooling. Herein, it is demonstrated for the first time that picosecond‐laser functionalization of copper surfaces—comprising densely packed, self‐organized, quasi‐periodic microstructures—results in surfaces that are highly suited for such applications. The methodology uses large laser beams (typical radius of 150µm or higher) to facilitate the self‐organization of laser‐formed surface features that are orders of magnitude smaller. The resulting laser‐functionalized surfaces not only exhibit excellent fluid transport capabilities, but also demonstrate exceptional heat transfer performance. Integrated into wickless vapor chambers (VCs), these surfaces enable device thermal resistances as low as 0.12 K W −1 at 0.3 MW m −2 load, and values ≈0.2 K W −1 across the range 0.3–1.5 MW m −2 —corresponding to almost 80% reduction compared to the thermal resistance of conventional wick‐lined VCs, as attested by a benchmarking study. Additionally, these functionalized surfaces have reduced sensitivity to working‐fluid charge ratio, proving their operational robustness. This work establishes a versatile, open‐atmosphere manufacturing route to functionalize surfaces for enhanced phase‐change heat transfer, unlocking low‐profile, high‐efficiency cooling solutions for next‐generation electronics.
11 April 2025 in ACS Applied Materials & Interfaces
Predicting the open‐surface movement of liquids on solids requires a fundamental understanding of adhesion and the interplay of frictional forces at the moving contact line. Frictional forces are commonly studied in two main contexts: (1) static and kinetic friction acting on droplets subjected to lateral forces, and (2) resisting (frictional) forces opposing the motion of advancing or receding liquid contact lines on solid surfaces. While conventional studies assume identical advancing and receding frictional forces for any liquid–solid pair, recent studies have challenged this notion, emphasizing the need for deeper insight into these forces, especially when the solid is rough. This study employs sessile‐droplet experiments for unpinned Wenzel (penetrating) states to quantify frictional forces at the triple‐phase contact line, revealing an empirical relationship between frictional force ratio and surface roughness. Contact angle (CA) measurements at constant contact‐line speeds under negligible viscous effects (Capillary number, Cα < <1) demonstrate that the advancing‐to‐receding friction force ratio scales solely with Wenzel roughness, being independent of liquid surface tension, viscosity, or chemical composition. This relationship enables accurate predictions of intrinsic CAs (<2% error) for wetting scenarios where experimental determination is challenging. The findings provide a predictive framework for characterizing new materials and their surface energies, while promoting the understanding and application of wetting dynamics on realistic (rough) surfaces.