Xunan Liu

Xunan Liu

Auto-generated profile, based on publicly available information

Xunan Liu

School of Mechanical Engineering, Liaoning Technical University, Fuxin, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2023 in Mechanics & Industry
Verified
Journal Article
Open access
PDF file
XLXunan Liu
Xunan Liu
XLXianglong Li
Xianglong Li
XFXin Fu
Xin Fu
XYXinle Yang
Xinle Yang
JZJianzhuo Zhang
Jianzhuo Zhang
Due to the great differences in mechanical properties between hard concretion and coal, the shearer drum cutting coal and rock containing hard concretion will inevitably lead to a series of problems, such as severe load impact, increased cutting specific energy consumption and low coal loading efficiency. Taking the cutting part of a thin coal seam shearer in service in the target mining area as the prototype, the mechanical models of shearer drum and rocker arm are established by using UG, and the discrete element model of coal wall with hard concretions is built by importing it into EDEM. The influence law of traction speed on coal loading rate, drum load and cutting specific energy consumption is analyzed, and the corresponding fitting relationship function is obtained. Taking the traction speed as the design variable, and the drum load, cutting specific energy consumption and coal loading rate as the comprehensive indicators, a multi-objective optimization function is established. The optimal solution is obtained by using NSGA II optimization algorithm, and the accuracy of the simulation is verified by experiments. This method has certain engineering significance for the reasonable selection of shearer traction speed.

1 November 2021 in Energy Reports
Verified
Journal Article
Open access
WLWeikang Li
Weikang Li
SBShujuan Bu
Shujuan Bu
XYXinle Yang
Xinle Yang
FHFeifei Huang
Feifei Huang
MTMeiling Tang
Meiling Tang
XLXunan Liu
Xunan Liu

4 April 2020 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
XLXunan Liu
Xunan Liu
CDChangqing Du
Changqing Du
MLMingxi Liu
Mingxi Liu
The cutting head is the key component of a road header in tunnel excavation, where the concept of the spiral angle design directly affects the comprehensive performance, which includes cutting resistance, fluctuation coefficient, specific energy consumption, cutting head stress distribution, and so on. Based on the theory of rock-breaking by pick, the mechanical model of pick was established, and the three-dimensional force vector in the WORKBENCH coordinate system was determined. The 3D model of the proposed cutting head was designed using PRO/E and the static simulation was carried out using WORKBENCH, while the stress information of key parts was obtained. Furthermore, a four-dimensional fitting method was used to investigate the influence of the horizontal swing speed, rotational speed, and spiral angle of the cutting head, on the stress of the cutting head assembly. By setting the horizontal swing speed, rotational speed and the spiral angle as design variables and the specific energy consumption, total cutting resistance, fluctuation coefficient, power consumption, and stress on cutting head assembly as the objective function; the multiobjective optimization function of the cutting head was established. By using genetic algorithm, the complex problem has been solved. The solution of this optimization function provides the horizontal swing speed, rotational speed, and spiral angle values, where the optimal performance is achieved, in the aspect of energy consumption, cutting resistance, fluctuation coefficient, cutting power, and cutting motor power. This method provides solid guidance and is a great reference in spiral angle design and optimization.

25 May 2023 in DYNA
Verified
Journal Article
Open access
PDF file
XLXunan Liu
Xunan Liu
YZYanpeng Zhang
Yanpeng Zhang
JWJie Wang
Jie Wang
HLHongye Li
Hongye Li
LMLianwei Ma
Lianwei Ma
Modeling and simulation of pick cutting hard concretion coal process are taken as a key link to analyze the stress variation law. To this aim, the properties of hard concretion coal in the target mining area were tested. Related model with high-quality common grid was generated using the mapping method through Hypermesh. the coal breaking process was performed using LS-DYNA, and the stress variation law of coal and hard concretion was analyzed. The results showed that the closer the action position to the middle point of long axis of hard concretion, the greater stress peak would be generated, stripping of the pick occurred when it acted on the 2/5 and 1/2 positions of the long axis. Using similarity theory, the model of hard concretion coal was made and the pick cutting experiment was performed. Compared with simulation torque result, the correctness of modeling and simulation has been verified.

2 May 2023 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
XLXunan Liu
Xunan Liu
ZZZhiqiang Zhao
Zhiqiang Zhao
XFXin Fu
Xin Fu
JZJianzhuo Zhang
Jianzhuo Zhang
XYXinle Yang
Xinle Yang
In tunnel construction, over-excavation and under-excavation by the roadheader often occur, which can lead to rough excavation cross-sections that require subsequent treatment resulting in additional time and cost. With a view to improving the quality of excavated tunnels, increasing the speed of the roadheader in tunneling applications, and accurately controlling the excavation process, a virtual prototype (VP) of the roadheader is built using Pro/Engineer, ADAMS, ANSYS, and EASY5. A mechanical model of the system is established and relationships between hydraulic piston expansion length, speed, and boom swing angle are determined. Then, a support vector regression (SVR) internal model controller is introduced into the roadheader swing system. An electromechanical fluid coupling automatic control system model is also established. Combining VP technology with the SVR algorithm, an internal model and inverse model of the roadheader horizontal swing system are obtained. Multi-domain co-simulations are performed. When the SVR internal model controller is incorporated, the gyration platform is more reliable, and the target position can be quickly tracked by the system. The cutting test bench of roadheader was built, and the cutting experiments were carried out by using SVR and PID control methods. Although the PID control system has a faster response, it is only 1.61 s faster than SVR, and the PID control method has a much higher over-excavation amount than SVR control method, and the maximum over-excavation amount is 3.22 times of SVR controller. Therefore, the SVR controller has better control over the over-excavation phenomenon and higher control accuracy. So the proposed method can be used to effectively solve the over-excavation and under-excavation problem.

15 July 2026 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Open access
XLXunan Liu
Xunan Liu
YDYongqiang Dong
Yongqiang Dong
JZJianzhuo Zhang
Jianzhuo Zhang
YWYadong Wang
Yadong Wang
LZLijuan Zhao
Lijuan Zhao
This study addresses the insufficient dynamic strength and low energy efficiency of continuous miners in complex coal seams. A rigid-flexible coupled virtual prototype of the EML340 miner revealed that stress at the cutting arm's hydraulic cylinder connection exceeds the allowable limit (125 MPa). Based on single-factor analysis of cutting parameters and coal-rock hardness, an intelligent Fuzzy Neural Network (FNN) controller was designed to optimize performance under stress constraints. Co-simulation using ADAMS and MATLAB/Simulink demonstrates that the system adaptively adjusts rotational and swing speeds in response to hardness variations. Compared with PID control, the FNN strategy reduces settling time by 87.5%, stress overshoot by 28.6%, and specific cutting energy by 9.3%, ensuring safety while enhancing efficiency. Simulation accuracy was validated via a physical cutting test bench, with a maximum relative error of 4.92% in vibration characteristics. This research provides a technical solution for achieving intelligent, efficient, and safe cutting in continuous miners.