24 January 2025 in International Journal of Low-Carbon Technologies
Findings from simulations and case studies reveal a significant reduction in energy consumption and CO2 emissions, with up to 30% improvement in overall energy efficiency. The framework demonstrates that combining natural light optimization with intelligent energy management systems can lead to sustainable building designs, fostering eco-friendly practices and reducing environmental footprints in urban infrastructure. Important results of the study show 24.81% environmental footprint reduction, 17.33% energy savings via daylight optimization, 92.75% energy efficiency gain, 94.39% effectiveness in energy management with Internet of Things integration, and 96.92% better illumination quality.
26 February 2025 in Sustainable Food Technology
The growing concern over environmental sustainability has prompted the development of various technologies for waste material recovery and management.
24 January 2025 in International Journal of Low-Carbon Technologies
Systems face challenges related to limited heat transfer efficiency and significant thermal losses, which reduce their overall performance. To address these issues, the proposed paper employs computational fluid dynamics (CFD) to model and simulate the performance of a solar water heater integrated with a dimple tube design. The CFD is an investigation of fluid flow and heat transfer characteristics. The experimental results demonstrated that the CFD model achieves an analysis of collector efficiency ratio of 60.2%, an analysis of Nusselt number of 270, an analysis of friction factor of 0.31, and an analysis of the concerning pressure of 3.65.
24 January 2025 in International Journal of Low-Carbon Technologies
This study proposes the type 2 fuzzy logic controller with genetic algorithm (T2FLC-GA) for optimal tracking of solar photovoltaic (PV) systems. The suggested technique improves the high-power transmission to loads under long-term weather conditions. Genetic algorithms (GAs) are search algorithms that use natural selection and genetic mechanisms to simultaneously find the near-optimal design for control rules and membership functions. The research proposes a control system that uses GA to increase a PV system’s output energy. This system adjusts the spatial angles of the solar panels along the vertical and horizontal axes. The numerical findings illustrate that the suggested T2FLC-GA model increases the accuracy rate of 98.5%, solar tracking rate of 96.5%, overall performance rate of 97.6%, computation cost rate of 10.5%, and power generation rate of 94.5% compared to other existing models.
6 January 2022 in International Journal for Simulation and Multidisciplinary Design Optimization
Forming micro-dimples nearer to the cutting edge on the rack face of the tungsten carbide cutting inserts will positively influence the machinability. However, it is challenging to machine the perfect micro-dimple dimensions by utilizing the available machining techniques. Finite element analysis can be an efficient way to observe the influence of dimple-texture area density, micro-dimple size, and various micro-dimple shapes on cutting inserts' machinability. This paper numerically analyses the impact of micro-dimple-textured cutting inserts in dry machining of AISI H-13 steel using AdvantEdge (virtual machining and finite element analysis software). Micro-dimples are formed on the rack face of tungsten carbide cutting inserts to observe the effect of dimple-textured cutting inserts on machinability compared to non-textured cutting inserts in terms of micro-dimple shape, micro-dimple size, and micro-dimple area density ratio. Their outcomes are analysed in terms of chip-insert contact length, main cutting force, and thrust force. It is observed that micro-dimple textured cutting inserts exhibit minimal main cutting force and thrust force in line with increasing the cutting insert life span. The abrasive wear was reduced in dimple-textured cutting inserts due to minimal contact between the cutting insert and chip developed compared to non-textured cutting inserts.
27 January 2026 in International Journal of Low-Carbon Technologies
Growing demand for high-efficiency solar thermal systems requires increased heat-transfer augmentation in parabolic trough-based water-heating applications. Low thermal conductivity in conventional working fluids reduces energy capture and unstable outlet temperatures. A unique Silver-Nanofluid Thermo-Hydraulic Multimodel (SNT-THM) technique addresses these constraints. The method combines a tailored silver nanofluid, optimized swirl-induced turbulence, and a hybrid computational fluid dynamics-based multimodel for thermo-hydraulic prediction and validation. Results indicate a 25%–40% increase in heat-transfer ratio, improved temperature uniformity, enhanced thermal efficiency, and acceptable pressure drops, demonstrating the feasibility of SNT-THM for next-generation high-performance solar water-heating collectors.