Ponnusamy Ragupathi

Ponnusamy Ragupathi

Auto-generated profile, based on publicly available information

Ponnusamy Ragupathi

Karpagam Academy of Higher Education

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 February 2023 in International Journal of Energy Research
Verified
Journal Article
Open access
PDF file
PRP. Ragupathi
P. Ragupathi
Debabrata BarikDebabrata Barik
Debabrata Barik
The present work explores a novel method of waste heat recovery (WHR) from the internal combustion (IC) engine and power generation using heat from hot exhaust gas (HEG) and thermoelectric generator (TEG). This system uses TEGs of aluminium oxide (Al2O3), bismuth telluride (Bi2Te3), lead telluride (PbTe3), and silicon germanium (SiGe) for the investigation of WHR and power generation. The experiments were conducted using a 5.9kW diesel engine as a source of heat and a heat exchanger (HE) with fins. The parameters such as variation in temperature, rate of heat recovery, rate of power generation, and conversion efficiency of TEGs were analyzed by varying the load on the engine from 0 to 100 with steps of 25 and different zones of the heat exchanger, namely, zone 1, zone 2, zone 3, and zone 4. During the experiment, it was observed that zone 2 gives a high-temperature difference compared to zone 1, zone 3, and zone 4. TEG of bismuth telluride (Bi2Te3) increases the heat recovery rate overall compared to Al2O3, PbTe3, and SiGe throughout the load spectrum and operating conditions concerning different zones. The maximum power generation by TEGs of Al2O3, Bi2Te3, PbTe3, and SiGe was found to be 6.35W, 7.18W, 6.41W, and 5.93W at zone 2 while the engine was operated at 75 of load, respectively. Bi2Te3 gives the highest conversion efficiency compared to other TEGs irrespective of the working zones. The thermal energy-to-electrical energy conversion efficiency was maximum of about 7.8 given by the TEG of Bi2Te3 at zone 2 while the engine was operated at 75 of the load.

29 April 2019 in Sustainable Environment Research
Verified
Journal Article
Open access
PDF file
SNSathiesh Kumar Nagaraj
Sathiesh Kumar Nagaraj
PPParanthaman Ponnusamy
Paranthaman Ponnusamy
GMGopal Pudhupalayam Muthukutti
Gopal Pudhupalayam Muthukutti
RPRagupathi Ponnusamy
Ragupathi Ponnusamy
The present study aims in developing an alternative energy solution for compression ignition engine with mixed bio oils from Jatropha and Pongamia (Karanja) vegetable. The high viscosity of the oil was reduced by preheating and transesterification process. The properties of the oil namely viscosity, density, calorific value and flash point were evaluated. The exhaust emissions of a single cylinder diesel engine were examined using 3 hole (3H) and 4 hole (4H) nozzle with 80:20 diesel and biodiesel ratio. The 3H nozzle exhibits the optimum emission levels as per the Indian norms. At no load condition, both 3H and 4H have the emission with same NOX composition while 4H produces more CO2 and least CO and HC. As the load increases the NOX gases emission increases wherein 4H produces more NOX gas than 3H nozzle. CO gas stabilized to 0.01% from the load of 2 kg itself for 4H whilst the 3H nozzle stabilized on 8 kg.

6 January 2022 in International Journal for Simulation and Multidisciplinary Design Optimization
Verified
Journal Article
Open access
PDF file
GVGanesan Vignesh
Ganesan Vignesh
Debabrata BarikDebabrata Barik
Debabrata Barik
ASAravind Samraj
Aravind Samraj
PRPonnusamy Ragupathi
Ponnusamy Ragupathi
MAMunusamy Arun
Munusamy Arun
Forming micro-dimples nearer to the cutting edge on the rack face of the tungsten carbide cutting inserts will positively influence the machinability. However, it is challenging to machine the perfect micro-dimple dimensions by utilizing the available machining techniques. Finite element analysis can be an efficient way to observe the influence of dimple-texture area density, micro-dimple size, and various micro-dimple shapes on cutting inserts' machinability. This paper numerically analyses the impact of micro-dimple-textured cutting inserts in dry machining of AISI H-13 steel using AdvantEdge (virtual machining and finite element analysis software). Micro-dimples are formed on the rack face of tungsten carbide cutting inserts to observe the effect of dimple-textured cutting inserts on machinability compared to non-textured cutting inserts in terms of micro-dimple shape, micro-dimple size, and micro-dimple area density ratio. Their outcomes are analysed in terms of chip-insert contact length, main cutting force, and thrust force. It is observed that micro-dimple textured cutting inserts exhibit minimal main cutting force and thrust force in line with increasing the cutting insert life span. The abrasive wear was reduced in dimple-textured cutting inserts due to minimal contact between the cutting insert and chip developed compared to non-textured cutting inserts.

1 February 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
PRP. Ragupathi
P. Ragupathi
Debabrata BarikDebabrata Barik
Debabrata Barik
SAS. Aravind
S. Aravind
GVG. Vignesh
G. Vignesh
The thermoelectric generators (TEGs) are devices that are utilized to convert the heat energy into electrical energy directly and the working principle of this device is based on See beck effect. Thermoelectric power production is a smart method for the direct translation of heat energy into an electrical one. This work explores a method to get the optimum process parameters on the performance of various TEGs by finding the conversion efficiency to recover the waste heat and converts it into electricity. For this purpose, an experimental setup was designed and fabricated to determine the performance of TEGs. The TEGs made by Bismuth Telluride (Bi2Te3), Lead Telluride (PbTe), and Aluminium Oxide (Al2O3) were taken for the performance analysis. The process variables are heat input, TEG material and temperature difference. The experiments were conducted by using Taguchi’s L9 orthogonal array to reduce the number of experiments. The results found that the heat input of 90W, TEG material of Bi2Te3 and the temperature difference of 75°C gives the maximum conversion efficiency of 2.45% from thermal to electrical energy. The statistical analysis of variance (ANOVA) showed that the most influential parameter on the performance of TEGs was heat input. The R2 and R2 (adj) values were found to be 93.25% and 86.50%, this shows that the developed model is significant and can predict the optimal solution.

27 December 2024
Verified
Book Chapter
Closed access
PDF file
MYM. Yuvaperiyasamy
M. Yuvaperiyasamy
NSN. Senthilkumar
N. Senthilkumar
BDB. Deepanraj
B. Deepanraj
PRP. Ragupathi
P. Ragupathi

31 December 2019 in Journal of Advanced Research in Dynamical and Control Systems
Verified
Journal Article
Closed access
ASAravind Samraj
Aravind Samraj
PRP. Ragupathi
P. Ragupathi