Mevlüt Arslan

Mevlüt Arslan

Auto-generated profile, based on publicly available information

Mevlüt Arslan

Department of Mechanical Engineering, Yozgat Bozok University, Yozgat 66200, Turkey

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 March 2023 in Science and Technology for Energy Transition
Verified
Journal Article
Open access
PDF file
ZYzeki yılbaşı
zeki yılbaşı
Murat Kadir YesilyurtMurat Kadir Yesilyurt
Murat Kadir Yesilyurt
MAMevlüt Arslan
Mevlüt Arslan
HYHayri Yaman
Hayri Yaman
In this study, it was aimed to examine the influences of biodiesel–diesel-higher alcohol (1-pentanol, 1-hexanol, and 1-heptanol) blends on the performance, emission and combustion behaviors of a single-cylinder diesel engine. The tests were performed at a fixed speed of 1500 rpm and variable loads (25%, 50%, 75%, and 100%). For the tests, 80% diesel and 20% hemp seed oil biodiesel were blended and called as B20. Biodiesel fuel was produced by transesterification from hemp seed oil in the presence of methanol and potassium hydroxide for the preparation of B20 binary test fuel and other ternary fuels. Furthermore, nine ternary blend fuels [20% HSOB + 70%, 60% and 50% diesel, respectively + 10%, 20% and 30% higher alcohol (pentanol, hexanol and heptanol) respectively] were prepared. The calculations made with the experimental data revealed that the minimum brake specific energy consumption values were 12,48 MJ/kW h, 13,06 MJ/kW h, 13,27 MJ/kW h, 13,35 MJ/kW h, 13,47 MJ/kW h, and 13,59 MJ/kW h, respectively, for diesel fuel at full load, for fuels B20, B20Hx10, B20Hp10, B20Hx20 and B20Pe10, the maximum brake thermal efficiency values were obtained as 28.85%, 27.56%, 27.14%, 26.97%, 26.73% and 26.49%, respectively, for the same fuels at the same load. The increment in higher alcohol concentration in the blend delayed start of combustion and therefore the ignition delay period was prolonged. In the fuel line pressure data, changes were observed depending on the amount, viscosity and density of the fuel. Furthermore, B20Hx10 and B20Hp10 fuels gave the maximum in-cylinder pressure, heat release rate, average gas temperature and pressure rise rate values after diesel and biodiesel. The addition of biodiesel and higher alcohol to diesel fuel resulted in a decrease in NOX, CO and unburned HC and smoke emissions and an increase in CO2. NOX, CO and unburned HC values of higher alcohol blended fuels at full load showed lower results, between 3.04–22.24%, 22.85–56.35% and 5.44–22.83%, respectively, compared to diesel fuel. It can be concluded that the use of hemp seed oil biodiesel and higher alcohol in the diesel engine will make a significant contribution to the reduction of NOX emissions.

13 July 2022 in Science and Technology for Energy Transition
Verified
Journal Article
Open access
PDF file
ZYzeki yılbaşı
zeki yılbaşı
Murat Kadir YesilyurtMurat Kadir Yesilyurt
Murat Kadir Yesilyurt
HYHayri Yaman
Hayri Yaman
MAMevlut Arslan
Mevlut Arslan
The core focus of the present investigation is regarding biodiesel production from industrial hemp seed oil applying single-stage homogenous catalyzed transesterification process obtaining high yield of methyl ester. The engine tests were carried out on a single-cylinder, four-stroke, water-cooled, unmodified diesel engine operating with hemp seed oil methyl ester as well as its blends with conventional diesel fuel. The experimental findings of the test fuels were compared with those from diesel. The results pointed out that the performance and combustion behaviors of biodiesel fuels are just about in line with those of diesel fuel propensity. The specific fuel consumption for 5% biodiesel blend (0.291 kg/kW h), 10% biodiesel blend (0.305 kg/kW h), and 20% biodiesel blend (0.312 kg/kW h) blends at full load was closer to diesel (0.275 kg/kW h). In the meantime, the thermal efficiency for biodiesel was found to be at the range of 15.98–24.97% and it was slightly lower than that of diesel (18.10–29.85%) at the working loads. On the other hand, the harmful pollutant characteristics of carbon monoxide, hydrocarbon, and smoke opacity for biodiesel and its blends were observed to be lower in comparison with diesel during the trials. However, the oxides of nitrogen emissions for biodiesel were monitored to be as 6.85–15.40 g/kW h which was remarkably higher than that of diesel (4.71–8.63 g/kW h). Besides that, the combustion behaviors of biodiesel and its blends with diesel showed much the same followed those of diesel. Namely, the duration of ignition delay of biodiesel–diesel blends was shorter than that of diesel fuel because of the higher cetane number specification of the methyl ester. The highest gas pressures inside the cylinder as well as the rates of the heat release of biodiesel including test fuels are lower in contrast to the diesel due to the shorter ignition delay. It could be concluded that the utilization of biodiesel produced from industrial hemp seed oil in the diesel engine up to 20% (by vol.) will decrease the consumption of diesel and environmental pollution, especially in developing countries.

2 July 2014 in International Journal of Automotive Engineering and Technologies
Verified
Journal Article
Open access
PDF file
TETanzer Eryılmaz
Tanzer Eryılmaz
Murat Kadir YesilyurtMurat Kadir Yesilyurt
Murat Kadir Yesilyurt
HYHasan Yumak
Hasan Yumak
MAMevlüt Arslan
Mevlüt Arslan
SŞSeda Şahin
Seda Şahin
In this study; density, kinematic viscosity, calorific value, flash point and water content of methyl ester produced from cottonseed oil (CO) were determined under varying blend ratio with ultimate euro diesel fuel, also density and kinematic viscosity were investigated at different temperatures. Six different fuel blends (3%, 5%, 10%, 25%, 50% and 75% by volume blending with diesel), cottonseed oil methyl ester (COME), cottonseed oil and diesel were used for experiments. Density of samples was measured 0-93oC interval with 5oC increments and kinematic viscosity of samples was measured 298.15-373.15 K interval with 5 K increments. All of the measurements were performed at 20oC room temperatures. It is found that; density, kinematic viscosity, calorific value, flash point and water content of cottonseed oil are 921.50 kg/m3, 31.347 mm2/s, 39.278 MJ/kg, 237oC and 232.90 mg/kg, respectively. For cottonseed oil methyl ester, they are 884.75 kg/m3, 4.713 mm2/s, 39.254 MJ/kg, 171oC and 499.19 mg/kg, respectively. The densities of each fuel sample decreased linearly with increasing temperature. But the kinematic viscosities of each fuel sample decreased exponentially with increasing temperature. In addition experimental results, the most commonly used prediction models were used to calculate the density and kinematic viscosity varying with temperature and blend ratio. Also calorific value, flash point and water content were correlated. Özet: Bu çalışmada; pamuk tohumu yağından (CO) üretilen metil ester içeriğinin yoğunluğu, kinematik viskozitesi, kalorifik değeri, parlama noktası ve su içeriği Euro dizel yakıtı ile çeşitli karışım durumlarında belirlenmiştir ve yoğunluk ile kinematik viskozite değeri farklı sıcaklıklarda incelenmiştir. Altı farklı karışım (dizel yakıtla hacimsel oranda %3, %5, %10, %25, %50 ve %75) pamuk tohumu metil esteri (COME), pamuk tohumu yağı ve dizel deneylerde kullanılmıştır. Numunelerin yoğunlukları 0-93 oC aralığında 5 oC artışlarla ölçülmüştür ve kinematik viskozite değerleri 298.15-373.15 K aralığında 5 K’lik artışlarla ölçülmüştür. Bütün ölçümler 20 oC oda sıcaklığında gerçekleştirilmiştir. Pamuk tohumu yağının yoğunluk, kinematik viskozite, kalorifik değer, parlama noktası ve su içeriğinin sırasıyla 921.50 kg/m3, 31.347 mm2/s, 39.278 MJ/kg, 237oC ve 232.90 mg/kg olduğu bulunmuştur. Pamuk tohumu yağı metil esteri için bu değerler sırasıyla 884.75 kg/m3, 4.713 mm2/s, 39.254 MJ/kg, 171oC ve 499.19 mg/kg olarak bulunmuştur. Her numunenin yoğunluğu sıcaklık ile doğrusal orantılı şekilde azalmıştır. Fakat numunelerin kinematik viskozite değerleri artan sıcaklığa bağlı olarak eksponansiyel biçimde azalmıştır. Deneysel sonuçlara ek olarak sıcaklığa ve karışım oranına bağlı şekilde yoğunluk ve kinematik viskozite değerleri sıkça kullanılan tahmin modelleri ile hesaplanmıştır. Ayrıca kalorifik değerler, parlama noktaları ve su içerikleri de matematiksel olarak ilişkilendirilmiştir.