Min-Chih Liao

Min-Chih Liao

Auto-generated profile, based on publicly available information

Min-Chih Liao

National Taiwan University of Science and Technology

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2016 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
MLMin-Chih Liao
Min-Chih Liao
CLChih-Chi Luo
Chih-Chi Luo
TWTai-Yen Wang
Tai-Yen Wang
XXXuecheng Xie
Xuecheng Xie
Cold-mix asphalt (CMA) is routinely used for temporary or emergency pothole repair to prevent further deterioration of the asphalt pavement until resurfacing can be performed. One of the difficulties encountered with CMA is that the majority of laboratory evaluations and tests were originally designed for hot-mix asphalt. There exists an incomplete understanding between viscosity gain of cold-mix binder (CMB) and strength development of CMA. The objective was to develop effective test procedures to assess the engineering properties and performance of the CMA. Results showed that the accelerated curing process with 110°C for 24 h has the potential for predicting the engineering properties of the CMAs at mature state. The stability and rutting resistance of the CMAs with high CMB viscosity appear to be comparable with those of hot-mix asphalt. The CMB viscosity of 13 Pa· s (130 poise) was suggested to specify the engineering properties and performance of the CMAs. In addition, simplified wheel trac...

19 January 2021 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Closed access
PDF file
DVDuy-Hai Vo
Duy-Hai Vo
CHChao-Lung Hwang
Chao-Lung Hwang
KTKhanh-Dung Tran Thi
Khanh-Dung Tran Thi
MLMin-Chih Liao
Min-Chih Liao
MYMitiku Damtie Yehualaw
Mitiku Damtie Yehualaw

21 September 2022 in Construction and Building Materials
Verified
Journal Article
Closed access
DVDuy-Hai Vo
Duy-Hai Vo
NDNgoc-Duy Do
Ngoc-Duy Do
YMYibas Mamuye
Yibas Mamuye
MLMin-Chih Liao
Min-Chih Liao
CHChao-Lung Hwang
Chao-Lung Hwang
TTThien Q. Tran
Thien Q. Tran

16 April 2022 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Closed access
PDF file
DVDuy-Hai Vo
Duy-Hai Vo
CHChao-Lung Hwang
Chao-Lung Hwang
KTKhanh-Dung Tran Thi
Khanh-Dung Tran Thi
MYMitiku Damtie Yehualaw
Mitiku Damtie Yehualaw
MLMin-Chih Liao
Min-Chih Liao
YLYun-Tai Lee
Yun-Tai Lee

14 June 2022 in Journal of Sustainable Cement-Based Materials
Verified
Journal Article
Closed access
DVDuy-Hai Vo
Duy-Hai Vo
CHChao-Lung Hwang
Chao-Lung Hwang
KTKhanh-Dung Tran Thi
Khanh-Dung Tran Thi
MYMitiku Damtie Yehualaw
Mitiku Damtie Yehualaw
MLMin-Chih Liao
Min-Chih Liao
HYHser Te Yu
Hser Te Yu
This study investigated the performance of alkali-activated slag (AAS) paste modified with different levels of styrene-acrylic resin (SAR) polymer latex. The AAS paste samples were prepared using GGBFS of two different fineness levels and NaOH solutions with respective molarities of 10 M, 12 M, and 14 M. Polymer latex was added at levels of 2.5%, 5%, and 7.5% of GGBFS weight. The AAS paste with fine GGBFS and NaOH 12 M performed the better strength than that with coarse GGBFS. The AAS paste samples modified with SAR polymer latex up to 5% exhibited slightly increased compressive strength results but reduced the ultrasonic pulse velocity (UPV) values. Furthermore, the addition of polymer latex enhanced the microstructure and significantly reduced efflorescence and drying shrinkage results. C-(A)-S-H gel and hydrotalcite phase were the main reaction products of both the latex-free and latex-modified AAS paste samples, with no new reaction products generated by the addition of polymer latex.

1 June 2022 in 3D Printing and Additive Manufacturing
Verified
Journal Article
Closed access
Aamer NazirAamer Nazir
Aamer Nazir
MLMin-Chih Liao
Min-Chih Liao
YZYan-Wei Zhu
Yan-Wei Zhu
UNUsman Nazir
Usman Nazir
Environmental protection and sustainability have been a serious challenge due to the excess amount of waste plastic, and the inefficient methods of its disposal. This study aims at exploring the feasibility of using plastic material in asphalt concrete followed by the design and evaluation of modified asphalt mix. Four different types of asphalt mixtures were made by mixing mineral aggregates with plastic aggregates of different shapes and sizes. The conventional dense-graded asphalt concrete incorporating mineral aggregates was selected as control material, whereas the other three types of asphalt mixtures were produced by substituting 3D-printed plastic aggregates for mineral aggregates. Marshall characteristics were utilized to evaluate the volumetric and mechanical properties of the asphalt mixtures. Test results show that the asphalt mixture containing solid plastic aggregate appears to have a 14.3% reduction in bulk density, thereby potentially reducing the haul costs. Due to the angular shape of the aggregate, the stability for the asphalt mixture containing the 3D-printed aggregate is 1.95 times higher than that for the asphalt mixture incorporating all mineral aggregates. The addition of the plastic printed aggregate enhances the strain capacity to achieve failure of the asphalt mixture. However, caution should be taken when incorporating the hollow or fine printed aggregates into the asphalt mixture due to their variation of volumetric properties.