Piezoelectric vibration energy harvesters (VEHs) with unimorph structure have been developed using Si micro-electrical mechanical systems (MEMS) technology. Since we revealed that (100) epitaxial BiFeO3 (BFO) piezoelectric films have high figure-of-merit on energy conversion, (100)-oriented BFO films have been prepared on (100)-oriented LaNiO3 bottom electrodes by the sol-gel method. We fabricated the piezoelectric VEHs using BFO films with resonance frequencies of ~100 Hz. The maximum output power density of these VEHs was determined to be 10.5 μWmm−3G−2 (G=9.8 ms−2) at a load resistance of 1 MΩ, which exceeds or is comparable to those of the best-performing VEHs using other piezoelectric films.
Vibration energy harvesters that use resonance phenomena exhibit a high output power density for constant frequency vibrations, but they suffer from a significant drop in performance for non-steady-state vibrations, which are important for practical applications. In this work, we demonstrate that the output power under an impulsive force can be increased significantly by placing a U-shaped metal component, called a dynamic magnifier (DM), under an MEMS piezoelectric vibration energy harvester (MEMS-pVEH) with a 6 mm long cantilever using a 3 μm thick Pb(Zr,Ti)O3 film. Based on the results of numerical calculations using a model of pVEH with a two-degree-of-freedom (2DOF) system, the DM was designed to have the same resonant frequency as the MEMS-pVEH and a high mechanical quality factor ( ). The waveforms of the output voltage of the fabricated 2DOF-pVEHs were measured for impulsive forces with various duration times, and the output power was calculated by integrating the waveforms over time. The output power of the MEMS-pVEH placed on the DM with a of 56 showed a gradual change according to the duration of applying an impulsive force and a maximum of 19 nJ/G2 (G: gravitational acceleration) when the duration of the impulsive force was 3.8 ms. This result was about 90 times greater than the output power of the MEMS-pVEH without a DM. While it is not easy to fabricate pVEHs with a complex 2DOF structure using only the MEMS process, we have demonstrated that the output power can be significantly improved by adding a spring structure to a simple MEMS-pVEH.
Enhancing the output power at small input acceleration is a major concern for enabling practical application of vibration energy harvesters. In this study, a two-degree of freedom system (2-DOF) was employed to solve this issue. The numerical calculations using the lumped parameter model of the piezoelectric vibration energy harvesters (pVEHs) with 2-DOF indicate that the harvesters show two resonance peak and an increase in the output power of several ten times compared with the harvester with a single degree of freedom. Based on calculations, the prototype of pVEH with 2-DOF was fabricated using a micro-machined pVEH and a metal cantilever. The output power of the harvester is 3.4 μW at 0.1 Grms, which is 17 times higher than that of the micro-electro-mechanical system-pVEH. Moreover, the resonance frequency on the pVEH with 2-DOF is easily adjusted because of the coupled vibration of the two masses.
We have enhanced magnetoresistance (MR) for current-perpendicular-to-plane giant-magnetoresistive (CPP-GMR) films with a current-confined-path nano-oxide layer (CCP-NOL). In order to realize higher purity in Cu for CCPs, hydrogen ion treatment (HIT) was applied as the reduction process. By applying the HIT process, an MR ratio was increased to 27.4% even in the case of using conventional FeCo magnetic layer, from 13.0% for a reference without the HIT process. Atom probe tomography data confirmed oxygen reduction by the HIT process in the CCP-NOL. The relationship between oxygen counts and MR ratio indicates that further oxygen reduction would realize an MR ratio greater than 50%.