13 August 2020 in Materials and Manufacturing Processes
RMRashed Mustafa Mazarbhuiya
Rashed Mustafa Mazarbhuiya
This work has described about the generation of complex shaped pattern using reverse electro discharge machining process. Powder metallurgical green compact tool has been used to generate a predefined pattern by depositing its constituent materials. A predefined star shaped pattern has been generated on the aluminum 6061 work surface. The pattern has been created by adjusting the process factors like compact load, current and pulse duration. The edge deviation and surface roughness have been considered as the performance measures in this experimentation. An optimum condition has been obtained at compact load of 20 tons, current of 1 A and pulse duration of 100 µs. Minimum surface roughness of 1.7 µm and minimum edge deviation of 13.07 µm have been achieved at this condition. The patterns are characterized by SEM, EDS and XRD analyses. The surface of the patterns is evaluated by a surface profilometer. The layer thickness is evaluated by an optical microscope. The microhardness of newly generated surface of pattern has been found to be of 329 Hv.
8 October 2019 in Materials and Manufacturing Processes
This article describes a process of pattern generation by selective area deposition of material on aluminum workpiece. Tungsten–copper powder metallurgical green compact tool and polyvinylchloride masking have been applied to deposit material at a selected area of the work surface. The rate of material transfer, surface roughness and edge deviation of the pattern has been considered as performance measures. Scanning Electron Microscope, Energy Disperse Spectroscopy and X-Ray Diffraction analyzes show the transfer of tool material to the selected area. The presence of tool material increases the surface hardness of the workpiece more than three times. However, hardness decreases toward the base material due to a gradual decrease of hard tool materials.
4 March 2022 in Surface Engineering
This article describes about the modification of graphite surface by depositing a hard layer of tungsten (W) and copper (Cu) material using electrical discharge machining (EDM) setup in reverse polarity. The sintered tool is prepared by heating a Powder Metallurgical (P/M) green compact of 75%W-25%Cu at 900 0C in an argon atmosphere. The deposited layer is studied by evaluating the Tool Wear Rate (TWR), Material Deposition Rate (MDR), and Surface Roughness (Ra). The coating is characterized by FESEM, EDS, and XRD analyses. The existence of tool particles (W and Cu) and carbides of tungsten (WC and W2C) are witnessed on the graphite surface. The tool materials are impinged up to 19.93 µm of depth from the surface level. The experimental results show an increase in thickness of the coating with increased peak current settings. Minimum thickness of 15.46 µm and maximum thickness of 33.93 µm are found in the experimentation.
4 March 2022 in Surface Engineering
Now-a-days carbon nanotube (CNT) is widely used because of its inimitable properties such as high electrical and thermal conductivities, high tensile strength, etc. In this work, an attempt has been made to modify the surface of Al-7075 alloy using Cu-MWCNT powder metallurgy green compact tool in the electric discharge machining process. The effects of contributing parameters i.e. peak current (Ip), voltage and compact load (CL) have been investigated with respect to performance measures such as, Material Deposition Rate (MDR), Tool Wear Rate (TWR) and Surface Roughness (Ra). The modified surface has been assessed by optical microscopy, FESEM, XRD and EDS analyses. Highest MDR of 0.15 mg min–1, lowest TWR of 2.05 mg min–1 and lowest Ra of 2.57 µm have been attained. The deposition of tool materials has improved the microhardness up to 2.6 times than that of base material.
23 November 2021 in Materials and Manufacturing Processes
This research work reports about pattern generation using the photochemical machining (PCM) assisted reverse electro discharge machining (EDM) process on an aluminum 6061 workpiece. A mixture of fine powder of copper and tungsten is used to fabricate a green compact tool. A complex shape is generated onto the tool surface and is further implemented to migrate the shaped tool particle onto the work surface. The output parameters are the material deposition rate (MDR), tool wear rate (TWR), edge deviation (ED), and surface roughness (Ra). The pattern is characterized by Field Emission Scanning Electron Microscopy (FESEM) and Energy Disperse Spectroscopy (EDS) analyses. The presence of tungsten particles increases the microhardness of the substrate material. The surface microhardness of the pattern is found to be 362Hv.