Justin Chow

Justin Chow

Auto-generated profile, based on publicly available information

Justin Chow

Georgia Institute of Technology

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 December 2016 in Scientific Reports
Verified
Journal Article
Open access
YFYunnan Fang
Yunnan Fang
JHJimmy G. D. Hester
Jimmy G. D. Hester
WSWenjing Su
Wenjing Su
JCJustin H. Chow
Justin H. Chow
SSSuresh K. Sitaraman
Suresh K. Sitaraman
MTManos M. Tentzeris
Manos M. Tentzeris
A bio-enabled, environmentally-friendly, and maximally mild layer-by-layer approach has been developed to surface modify inherently hydrophobic Kapton HN substrates to allow for great printability of both water- and organic solvent-based inks thus facilitating the full-inkjet-printing of flexible electronic devices. Different from the traditional Kapton surface modification approaches which are structure-compromising and use harsh conditions to target, and oxidize and/or remove part of, the surface polyimide of Kapton, the present Kapton surface modification approach targeted the surface electric charges borne by its additive particles, and was not only the first to utilize environmentally-friendly clinical biomolecules to build up a thin film of protamine-heparin complex on Kapton, but also the first to be conducted under minimally destructive and maximally mild conditions. Besides, for electrically charged ink particles, the present surface modification method can enhance the uniformity of the inkjet-printed films by reducing the “coffee ring effect”. As a proof-of-concept demonstration, reduced graphene oxide-based gas sensors, which were flexible, ultra-lightweight, and miniature-sized, were fully-inkjet-printed on surface modified Kapton HN films and tested for their sensitivity to dimethyl methylphosphonate (a nerve agent simulant). Such fabricated sensors survived a Scotch-tape peel test and were found insensitive to repeated bending to a small 0.5 cm radius.

8 November 2012 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
YTYe Tian
Ye Tian
JCJustin Chow
Justin Chow
XLXi Liu
Xi Liu
YWYi Ping Wu
Yi Ping Wu
SSSuresh K. Sitaraman
Suresh K. Sitaraman

30 August 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
RCRui Chen
Rui Chen
JCJustin H. Chow
Justin H. Chow
YZYi Zhou
Yi Zhou
JMJeffrey S. Meth
Jeffrey S. Meth
SSSuresh K. Sitaraman
Suresh K. Sitaraman
Flexible electronics are becoming more and more widely used in all fields, such as wearable devices, flexible displays, flexible sensors, and so on. Therefore, it is essential to investigate the reliability of flexible electronics under various loading conditions. In this article, the mechanical and electrical behavior of printed conductors was tested under reciprocating adaptive curvature flexure bending. The silver-ink conductors of different widths were screen-printed on polyimide (PI) and polyethylene terephthalate (PET) substrates and served as the samples. Through the tests, the resistance of the conductors was measured by a four-wire method continuously. The tests were carried out under different gap distances and moving ranges. Besides the tests, SEM imaging was also performed to understand the microstructure change of the printed conductor before, during, and after the tests. Finite-element simulations were performed to track the strain history of specific locations of the printed conductor. Finally, a two-stage process of resistance increase was identified in the reciprocating adaptive curvature flexure test. The resistance change of the conductors under different loading conditions was determined. The parameters that affect the resistance change were also figured out. Cracks and delamination in the printed conductor were observed and related to the resistance increase phenomena under small tensile and compressive bending radius, respectively.

1 May 2019
Verified
Conference Paper
Closed access
JCJustin H. Chow
Justin H. Chow
JMJeffrey Meth
Jeffrey Meth
SSSuresh K. Sitaraman
Suresh K. Sitaraman
Electronic devices have found use in a variety of flexible form factors such as wearable health monitoring devices, fitness trackers integrated into garments, etc. These form factors expose the electronic components (printed traces, passives, active devices, etc.) to a wide range of mechanical strains that are not typically seen in traditional rigid devices. In fact, the utility of these devices depends on its ability to stretch, bend, fold, and/or twist. As such, there is a need for methods and standards for testing these devices under these mechanical loads. In our ongoing work, we have conducted extensive stretch and bend testing of conductors, co-planar waveguides, antennas, and other elements. Both monotonic and fatigue testing of some of these components have also been carried out. In this paper we describe the development of a test apparatus that can subject flexible electronic test coupons to controlled twists while monitoring in-situ the electrical resistance of the printed conductor. Unlike in stretch testing, in twist testing buckling of the samples is a concern, and thus, appropriate models have been used to ensure that the substrates are subjected to pure twisting without any apparent buckling of the sample. Samples were subjected to twist angles ranging from ± 30° to ± 135° and the resulting resistance was measured in-situ. Both polyimide and PET substrates with screen-printed silver conductors have been tested and the results have been presented for both monotonic and cyclic loadings. The thermal coefficient of resistance (TCR) of screen-printed silver ink has been measured to be 0.00233 per °C and accounted for in the twist resistance measurements to reduce the temperature effect on resistance during long-term cyclic twist testing. Cyclic twisting to ±135° or shear strains of ± 2.99 x 10-3 induced minimal changes in resistance (less than 1.5%) over 5000 cycles.

15 February 2014 in Microelectronics Reliability
Verified
Journal Article
Closed access
YTYe Tian
Ye Tian
XLXi Liu
Xi Liu
JCJustin Chow
Justin Chow
YWYi Ping Wu
Yi Ping Wu
SSSuresh K. Sitaraman
Suresh K. Sitaraman

3 April 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
RCRui Chen
Rui Chen
JCJustin H. Chow
Justin H. Chow
CTChristine Taylor
Christine Taylor
JMJeffrey Meth
Jeffrey Meth
SSSuresh K. Sitaraman
Suresh K. Sitaraman
Flexible electronic products are becoming increasingly popular. Because of the large deformation that flexible products encounter, it is important to predict their performance in response to mechanical loadings. This paper focuses on the mechanical and electrical behavior of the printed silver conductor under the adaptive curvature flexure test. In the adaptive curvature flexure test, the printed conductor is bent between two rigid parallel plates so that the bending strain will be generated through the conductor and thus cause resistance change. The resistance of the conductor was measured continuously by the 4-wire method during the test for analysis. A series of conductors with different widths printed on two commonly used substrate materials—polyimide and polyethylene terephthalate—were tested. In the single load-unload tests, the resistance of the conductor increased nonlinearly as the gap distance between the parallel plates decreased. Cracks in the conductor were observed under a strain of approximately 3%. In the cyclic tests, the resistance of the conductor increased linearly with cycles after the first several cycles. In addition to the experimental tests, the strain distribution of the conductor was calculated by both finite element method and theoretical analysis. Combined with the relationship between the resistivity of the conductor and the bending strain, an integral model has been developed to predict the resistance change of the printed conductor under bending.