1 May 2016 in Applied Surface Science
The influence of deposition conditions on the residual stress of sputtered tantalum thin-film has been evaluated in the present study. Films have been deposited by DC magnetron sputtering and curvature measurement method has been employed to calculate the residual stress of the films. Transitions of tantalum film stress from compressive to tensile state have been observed as the sputtering pressure increases. Also, the effect of annealing process at temperature range of 90–300°C in oxygen ambient on the residual stress of the films has been studied. The results demonstrate that the residual stress of the films that have been deposited at lower sputtering pressure has become more compressive when annealed at 300°C. Furthermore, the impact of exposure to atmospheric ambient on the tantalum film stress has been investigated by monitoring the variation of the residual stress of both annealed and unannealed films over time. The as-deposited films have been exposed to pure Argon energy bombardment and as result, a high compressive stress has been developed in the films
1 May 2019 in IEEE Sensors Journal
We fabricate a MEMS microphone that incorporates a graphene-based membrane that vibrates in response to acoustic forcing. We employ a novel fabrication process, where a graphene/PMMA bilayer membrane is transferred over a cavity on a separate chip before being affixed to the surface of another chip containing an electrode, resulting in the fabrication of a moveable capacitor with a membrane-to-electrode gap of 8 μm. The gap, which is less than half the size of other reported graphene membrane-based audio transducers, allows for the device to operate with low DC bias voltages of about 1 V and, when integrated with a custom-designed readout circuit, demonstrates a sensitivity to sound pressure between 0.1 mV/Pa and 10 mV/Pa across the range 100 Hz to 20 kHz. As well as a sensitivity that is comparable to previous work, the flat frequency response is stable when the sound pressure is varied between 70 dBSPL and 80 dBSPL, with the sensitivity value not varying by more than 0.2 mV/Pa.
11 December 2017 in Applied Physics Letters
This letter reports an experimental study of an electrothermal actuator made from an ultra-large graphene-based bilayer thin film with a diameter to thickness aspect ratio of ∼10 000. Suspended thin films consisting of multilayer graphene and 350–500 nm-thick Poly(methyl methacrylate) have been transferred over circular cavities with a diameter of 3.5 mm. The use of bilayer materials with different mechanical and thermal properties results in thin film structures that can be induced to vibrate mechanically under the electrothermal transduction mechanism. The dynamic response of the bilayer has been investigated electrothermally by driving the structures with a combination of alternating current and direct current actuation voltages ( and ) and characterizing their resonant frequencies. It has been found that the bilayer thin film structure behaves as a membrane. In addition, the actuation configurations affect not only the amplitude of vibration but also the tuning of the resonant frequency of the vibrating membranes. The existence of Joule heating-induced tension lowers the mechanical stiffness of the membrane and hence shifts the resonant frequency downwards by −108187 ppm. A resonant frequency of 3.26 kHz with a vibration amplitude of 4.34 nm has been achieved for 350 nm-thick membranes under actuation voltages of 1 V of and 8 V of .
13 January 2020 in IEEE Sensors Journal
16 November 2016 in Journal of Micromechanics and Microengineering
An investigation of the influence of deposition and post-fabrication processes on the final mechanical structure of tantalum beams is reported in the present study. The final deflection profiles of doubly supported beams made from compressive and tensile-stressed films have been studied experimentally. An optimum finite element model has been developed to predict the buckling behaviour of the doubly supported beams by considering the boundary conditions in the form of a compressive stress and an applied load. No matter which etch release method has been used, the initial stress state of the as-deposited films has been found to have a significant impact on the final deflection profile of the fabricated device. The compressive-stressed films have presented larger deflection in the final released beams than the tensile-stressed films. Taking into account the type of etch release methods, the beams that have been released in the dry etch release processes have been found to deform more vertically than those released in the wet-etch release method. Moreover, it has been found that the amplitude of vertical deflection increases with the increase of the beam length and thickness. The results indicate that optimum profiles of tantalum suspended structures can be obtained from the tensile-stressed films that have been released by the wet etching method with an aspect ratio of 1:48.
1 March 2018 in Electronics Letters
This Letter presents the design, fabrication and characterisation of an array of electrostatically actuated clamped–clamped microbeams. A large bottom actuation electrode and long beams with lengths ranging from 1 to 3.4 mm are the major features of the present device. The novelty of this Letter lies in the realisation of suspended and undeformed microstructures by controlling the process‐induced stress during the fabrication process. This has been achieved by compensating the influence of the compressive and tensile stress components of the different deposited layers, resulting in ultralong beams with a relatively straight mechanical profile and an aspect ratio of ∼1:3400 of vertical deflection to the beam length. For the first time, ultralong microbeams of tantalum have been actuated electrostatically with AC and DC driving voltages to drive them into resonance and characterise their resonant frequencies. The lowest resonant frequency of 1.4 kHz is obtained for a 3.4 mm‐long beam. The shift of the resonant frequency due to the effect of different DC biasing has been investigated experimentally. A spring softening effect has been induced through electrostatic tuning. A downward shift in the resonant frequency to 35,000 ppm for DC bias voltages increasing from 1 to 5 V has been demonstrated.