Tanattha Rattana

Tanattha Rattana

Auto-generated profile, based on publicly available information

Tanattha Rattana

Department of Physics, Faculty of Science, Burapha University, Chonburi, 20131, Thailand

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2020 in Thin Solid Films
Verified
Journal Article
Closed access
PKPhalakorn Khwansungnoen
Phalakorn Khwansungnoen
SCSurasing Chaiyakun
Surasing Chaiyakun
TRTanattha Rattana
Tanattha Rattana

1 November 2021 in Vacuum
Verified
Journal Article
Closed access
PKPhalakorn Khwansungnoen
Phalakorn Khwansungnoen
TCTheeranon Chaiyakun
Theeranon Chaiyakun
SSSumetha Suwanboon
Sumetha Suwanboon
TRTanattha Rattana
Tanattha Rattana

26 December 2022 in Coatings
Verified
Journal Article
Open access
PDF file
WPWuttichai Phae-ngam
Wuttichai Phae-ngam
TRTanattha Rattana
Tanattha Rattana
SKSurachart Kamoldilok
Surachart Kamoldilok
KKKanokporn Kohmun
Kanokporn Kohmun
Hideki NakajimaHideki Nakajima
Hideki Nakajima
Mati HorprathumMati Horprathum
Mati Horprathum
Silver–tantalum (Ag–Ta) thin films were fabricated by magnetron co-sputtering on silicon (Si) wafer (100) and glass slide substrates at room temperature. The Ag–Ta thin films were prepared at various deposition times of 5, 10, 20 and 30 s and the physical, structural and optical properties of the Ag–Ta thin films were investigated. It was determined that the thicknesses of the films were 7, 9, 17 and 33 nm, respectively. The results revealed that an increase in the film thickness leads to a monotonic increase in FCC and BCC phase of Ag and Ta, respectively. The work function and stoichiometric of the Ag–Ta thin films were investigated by ultraviolet and X-ray photoemission spectroscopies (UPS and XPS), respectively. The potential of Ag–Ta thin films to be used as low-emission coating was investigated using a spectrophotometer. A UV–VIS–NIR spectrophotometer was used to measure the spectral reflectance in the wavelength range from 300 to 2000 nm. The results showed that the Ag–Ta thin film deposited for 30 s exhibited higher reflectance in NIR region than those of 5, 10, 20 and 30 s. It demonstrated an average reflectance of about 80% and slightly decreased to 75% after being kept in the air atmosphere for 28 days. It can be likewise proposed as an alternative thin film with high reflectance of NIR radiation single layer to develop industrial low-emission coating for cost-effective, clean, and easy adaptation to a large area coating.

1 September 2021 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
PKPhalakorn Khwansungnoen
Phalakorn Khwansungnoen
ACAttapol Choeysuppaket
Attapol Choeysuppaket
TRTanattha Rattana
Tanattha Rattana
Thin films of titanium oxynitride deposited via reactive direct current (DC) magnetron sputtering method followed by annealing treatment at 500 °C for crystallization improvement. The thin films were grown under the Ar/O2/N2 gases mixture by various nitrogen ratios. The crystalline structure, surface morphology, and optical properties of the obtained thin films were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), and ultraviolet-visible spectrophotometer, respectively. The rutile to anatase phase transition could be detected that increased with increasing the nitrogen ratio and also affected the crystallite size and the thickness of the thin films. The optical bandgap evaluated by the Tauc plot is in the range of 2.78–3.17 eV.

20 October 2021 in Surface Review and Letters
Verified
Journal Article
Closed access
PDF file
WPWuttichai Phae-ngam
Wuttichai Phae-ngam
TRTanattha Rattana
Tanattha Rattana
SSSupphadate Sujinnapram
Supphadate Sujinnapram
CCChanunthorn Chananonnawathorn
Chanunthorn Chananonnawathorn
UWUraiwan Waiwijit
Uraiwan Waiwijit
JCJaroenporn Chokboribal
Jaroenporn Chokboribal

24 November 2025 in Journal of Metals, Materials and Minerals
Verified
Journal Article
Open access
PDF file
CKChittra Kedkaew
Chittra Kedkaew
PKPhalakorn Khwansungnoen
Phalakorn Khwansungnoen
TRTanattha Rattana
Tanattha Rattana
Ti-Cu alloy thin films exhibit considerable potential for the development of advanced antibacterial surfaces, particularly for biomedical applications. In this research, Ti-Cu binary alloy thin films with a wide range of Cu content from 25.8 at% to 77.8 at% were deposited using magnetron co-sputtering with pure Ti and Cu as the targets. The composition of Cu in the films can be controlled by the applied power of Cu targets. This study investigated the effect of Cu content on the microstructural, morphological, and antibacterial properties using X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and plate-count method, respectively. Structural analysis using XRD revealed that Ti (Cu) solid solution is formed for the Ti-Cu coatings with the Cu contents of 25.8 at% and the films tended to form an amorphous structure embedded with Cu nanocrystals when the Cu content was 77.8 at%. Surface morphology showed that the films with higher Cu content exhibited increased surface roughness and the presence of Cu nano-granular features. Antibacterial evaluations against Escherichi coli showed that the films containing Cu in the range of 25.8 at% to 77.8 at%. This effect is attributed to both inherent antibacterial properties by Cu and the microstructural modifications that enhance bacterial inhibition.