Joanna Panek

Joanna Panek

Auto-generated profile, based on publicly available information

Joanna Panek

University of Silesia, Institute of Material Science, 75 Pułku Piechoty 1A, 41-500 Chorzów, Poland

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2003 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
JPJ Panek
J Panek
ASA Serek
A Serek
ABA Budniok
A Budniok
ERE Rowinski
E Rowinski
EAE Agiewka
E Agiewka

1 February 2016 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
Małgorzata KarolusMałgorzata Karolus
Małgorzata Karolus
JPJ. Panek
J. Panek

2 April 2007 in Surface and Coatings Technology
Verified
Journal Article
Closed access
JPJoanna Panek
Joanna Panek
ABAntoni Budniok
Antoni Budniok

13 February 2008 in Surface and Interface Analysis
Verified
Journal Article
Open access
PDF file
JPJ. Panek
J. Panek
ABA. Budniok
A. Budniok
Composite Ni + Mo coatings were obtained by electrodeposition of Ni with Mo particles on a steel substrate from the nickel bath in which metallic Mo powder was suspended by stirring. Deposits were characterized by the presence of Mo particles embedded into the crystalline nickel matrix. Incorporation of metallic powder into electrolytic nickel matrix causes an increase in the real surface area of deposits. The composite coatings obtained were tested as electrode materials for hydrogen evolution reaction (HER) in an alkaline environment. Electrochemical characterization of the composites was carried out by steady‐state polarization method and electrochemical impedance spectroscopy (EIS) measurements. It was ascertained, that Ni + Mo coatings are characterized by enhanced electrochemical activity for this process, which was confirmed by considerable decrease in the hydrogen evolution overpotential at the current density of 100 mA cm −2 − η 100 , by a nearly 170–260 mV compared to nickel electrode. Exchange current density j 0 increases with the increase in Mo content in the coatings. Based on the results of EIS measurements, the rate constants of the HER for Ni and Ni + 44%Mo coatings were determined. The calculated values of surface roughness factor R f allowed also to evaluate the influence of the real surface area on the electrocatalytic performance of these materials in an alkaline environment. It was stated that the improvement of the electrocatalytic performance of Ni + Mo composite coatings could be attributed to the increase in their real surface area as well as to the synergetic effect of molybdenum with the nickel matrix, as Ni/Mo materials are considered in literature, typical electrocatalysts for the HER. Copyright © 2008 John Wiley & Sons, Ltd.

28 March 2014 in Surface and Interface Analysis
Verified
Journal Article
Closed access
PDF file
JPJoanna Panek
Joanna Panek
JKJulian Kubisztal
Julian Kubisztal
BBBożena Bierska‐Piech
Bożena Bierska‐Piech

28 November 2019 in Materials
Verified
Journal Article
Open access
PDF file
EMEwa Malicka
Ewa Malicka
Małgorzata KarolusMałgorzata Karolus
Małgorzata Karolus
TGTadeusz Gron
Tadeusz Gron
AGAdrian Gudwański
Adrian Gudwański
AŚAndrzej Ślebarski
Andrzej Ślebarski
JPJoanna Panek
Joanna Panek
Structural, electrical, magnetic, and specific heat measurements were carried out on ZnCr2Se4 single crystal and on nanocrystals obtained from the milling of this single crystal after 1, 3, and 5 h, whose crystallite sizes were 25.2, 2.5, and 2 nm, respectively. For this purpose, the high-energy ball-milling method was used. The above studies showed that all samples have a spinel structure, and are p-type semiconductors with less milling time and n-type with a higher one. In turn, the decrease in crystallite size caused a change in the magnetic order, from antiferromagnetic for bulk material and nanocrystals after 1 and 3 h of milling to spin-glass with the freezing temperature Tf = 20 K for the sample after 5 h of milling. The spin-glass behavior for this sample was derived from a broad peak of dc magnetic susceptibility, a splitting of the zero-field-cooling and field-cooling susceptibilities, and from the shift of Tf towards the higher frequency of the ac susceptibility curves. A spectacular result for this sample is also the lack of a peak on the specific heat curve, suggesting a disappearance of the structural transition that is observed for the bulk single crystal.