Progress on the fabrication of ultrahigh-Q photonic-crystal nanocavities (PhC-NCs) has revealed the prospect for new applications including silicon Raman lasers that require a strong confinement of light. Among various PhC-NCs, the highest Q has been recorded with silicon. On the other hand, microcavity is one of the basic building blocks in silicon photonics. However, the fusion between PhC-NCs and silicon photonics has yet to be exploited, since PhC-NCs are usually fabricated with electron-beam lithography and require an air-bridge structure. Here we show that a 2D-PhC-NC fabricated with deep-UV photolithography on a silica-clad silicon-on-insulator (SOI) structure will exhibit a high-Q of 2.2 × 105 with a mode-volume of ~1.7(λ/n)3. This is the highest Q demonstrated with photolithography. We also show that this device exhibits an efficient thermal diffusion and enables high-speed switching. The demonstration of the photolithographic fabrication of high-Q silica-clad PhC-NCs will open possibility for mass-manufacturing and boost the fusion between silicon photonics and CMOS devices.
We demonstrate ultrasmall demultiplexers based on photolithographic photonic crystals. The footprint of the demultiplexers is 110 μm2 per channel. Our in-plane demultiplexers are clad with silica, which makes them stable and easy to integrate with other silicon photonic devices. We describe two types of demultiplexers with spacings of 136 and 267 GHz between channels for application to dense wavelength division multiplexing. Integrated titanium nitride heaters allow us to precisely control the channel wavelength. We report a 2.5 Gbps transmittance experiment with sufficiently small crosstalk and discuss ways of achieving even lower crosstalk between channels.
In this Letter, we experimentally demonstrate low noise 300 GHz wave generation based on a Kerr microresonator frequency comb operating in the soliton regime. The spectral purity of a 10 GHz GPS-disciplined dielectric resonant oscillator is transferred to the 300 GHz repetition rate frequency of the soliton comb through an optoelectronic phase-locked loop. Two adjacent comb lines beat on a uni-traveling carrier photodiode emitting the 300 GHz millimeter-wave signal into a waveguide. In an out-of-loop measurement, we measure the 300 GHz power spectral density of phase noise to be , at 10 kHz, and 1 MHz Fourier frequency, respectively. Phase-locking error instability reaches at 1 s averaging time. Such a system provides a promising path to the realization of compact, low power consumption millimeter-wave oscillators with low noise performance for out-of-the-laboratory applications.
Dissipative Kerr-microresonator soliton combs (hereafter called soliton combs) are promising to realize chip-scale integration of full soliton comb systems providing high precision, broad spectral coverage, and a coherent link to the micro/mm/THz domain with diverse applications coming on line all the time. However, the large soliton comb spacing hampers some applications. For example, for spectroscopic applications, there are simply not enough comb lines available to sufficiently cover almost any relevant absorption features. Here, we overcome this limitation by scanning the comb mode spacing by employing Pound–Drever–Hall locking and a microheater on the microresonator, showing continuous scanning of the soliton comb modes across nearly the full free-spectral range of the microresonator without losing soliton operation, while spectral features with a bandwidth as small as 5 MHz are resolved.
All-optical tunable buffering was recently achieved on a chip by using dynamically tuned coupled mode induced transparency, which is an optical analogue of electromagnetically induced transparency. However, the small Q s of about 105 used in those systems were limiting the maximum buffering time to a few hundred ps. Although employing an ultra-high Q whispering gallery mode (WGM) microcavity can significantly improve the maximum buffering time, the dynamic tuning of the WGM has remained challenging because thermo-optic and pressure tunings, which are widely used for WGM microcavities, have a very slow response. Here we demonstrate all-optical tunable buffering utilizing coupled ultra-high Q WGM cavities and the Kerr effect. The Kerr effect can change the refractive index instantaneously, and this allowed us to tune the WGM cavity very quickly. In addition, from among the various WGM cavities we employed a silica toroid microcavity for our experiments because it has an ultra-high Q factor (>2 × 107) and a small mode volume, and can be fabricated on a chip. Use of the Kerr effect and the silica toroid microcavity enabled us to observe an on-chip all-optical tunable buffering operation and achieve a maximum buffering time of 20 ns.