Debora da Silva Rodrigues

Debora da Silva Rodrigues

Auto-generated profile, based on publicly available information

Debora da Silva Rodrigues

Engineering Center Federal University of Pelotas (UFPel) Pelotas Rio Grande do Sul Brazil

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2025 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
MBMariane Weirich Bosenbecker
Mariane Weirich Bosenbecker
ESEduarda Vieira Silva
Eduarda Vieira Silva
PSPATRICIA OLIVEIRA SCHMITT
PATRICIA OLIVEIRA SCHMITT
TZTiago Thomaz Migliati Zanon
Tiago Thomaz Migliati Zanon
DRDébora da Silva Rodrigues
Débora da Silva Rodrigues
AOAmanda Oliveira
Amanda Oliveira
This study investigates low‐density green polyethylene (LDPE) nanocomposites reinforced with bamboo‐derived cellulose nanocrystals (CNCs) and compatibilized with polyethylene‐graft‐maleic anhydride (PE‐g‐MA). Four materials were prepared by melt extrusion and injection molding (neat LDPE; LDPE with 1.0 and 1.5 wt% CNCs; and LDPE with 1.0 wt% CNC + 1.0 wt% PE‐g‐MA) and evaluated by thermal, mechanical, and structural analyses. Fourier‐transform infrared spectroscopy (FTIR) indicated interactions between maleic‐ anhydride groups and CNC hydroxyls, supporting improved interfacial compatibility. X‐ray diffraction (XRD) showed increased crystallinity in CNC‐containing samples, consistent with a nucleating effect. Thermogravimetric analysis/derivative thermogravimetry revealed single‐step LDPE decomposition with an upward shift of the degradation‐rate peak upon CNC addition; residues remained below at these low loadings. Under uniaxial tension, stiffness increased significantly at 1.5 wt% CNC and in the compatibilized composite, while tensile strength improved only with PE‐g‐MA; elongation decreased with CNCs irrespective of compatibilizer, remaining highest for neat LDPE. After accelerated aging (UV + humidity), modulus and strength exhibited modest declines across all materials, comparatively larger in the compatibilized system, suggesting time‐dependent changes at the CNC‐matrix interface. Overall, bamboo‐CNC/PE‐g‐MA provides a sustainable route to tailor thermal performance and load‐bearing response of LDPE for applications that prioritize stiffness and thermal resistance over ductility.

9 September 2026 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
PDF file
PSPATRICIA OLIVEIRA SCHMITT
PATRICIA OLIVEIRA SCHMITT
CNCHIARA DAS DORES DO NASCIMENTO
CHIARA DAS DORES DO NASCIMENTO
Everton Granemann SouzaEverton Granemann Souza
Everton Granemann Souza
Lincoln Audrew CordeiroLincoln Audrew Cordeiro
Lincoln Audrew Cordeiro
ACAndré Lamounier Caixeta
André Lamounier Caixeta
André Luiz MissioAndré Luiz Missio
André Luiz Missio
Composition‐tunable lignocellulosic aerogels were produced from Eucalyptus spp. bark as adsorbents without additional chemical functionalization. Four formulations comprising cellulose, lignin, and microfibrillated cellulose (MFC) were freeze‐dried: cellulose (CEL), cellulose/MFC (CEL‐M), lignin/MFC (L‐M), and cellulose/lignin/MFC (CEL‐L‐M) aerogels. The samples were characterized by SEM, nitrogen physisorption, XRD, FTIR, density, and porosity. All aerogels exhibited ultralow density and porosity above 99%, with composition‐dependent fibrillar organization, crystallinity, and pore architecture. Bru nauer–Emmett–Teller (BET) surface areas ranged from 0.95 to 7.37 m 2 g −1 for as‐synthesized samples and reached 18.38 m 2 g −1 after Cu 2+ adsorption. CEL showed the highest used cooking‐oil uptake (approximately 40 g g −1 ), whereas CEL‐M performed best for used pump oil (38.81 g g −1 ). Cu 2+ adsorption increased from pH 2 to pH 4–5; CEL‐L‐M reached the highest capacity (1.1337 g g −1 ) at pH 5 after 30 min, while L‐M reached 0.8964 g g −1 within 15 min and remained above 1.06 g g −1 from 30 to 60 min. FTIR changes and Cu detection by EDS supported pH‐regulated binding at oxygen‐containing sites. Accordingly, cellulose, lignin, and MFC contributed differently: CEL maximized cooking‐oil uptake, CEL‐M maximized pump‐oil uptake, while L‐M and CEL‐L‐M provided the fastest Cu 2+ uptake and highest capacity, respectively.