This study investigates the sustainable use of Eucalyptus spp. bark through different chemical (hydrothermal, acid, alkaline, and bleaching) and physical (milling) pretreatments in the production of sustainable films. Valorization of agro-industrial residues and the demand for sustainable materials pose challenges for environmentally responsible solutions. Eucalyptus spp. bark, rich in cellulose, hemicellulose, and lignin, is a promising source for creating sustainable materials like films. In this study, the use of chemical and physical treatments aims to optimize biomass extraction and improve the chemical, thermal, mechanical, and optical properties of the films. The films showed an excellent light barrier capacity, with a transmittance below 1%. Crystallinity indices varied with the pretreatment: 8.15% for hydrothermal, 7.01% for alkaline, 7.63% for acid, and 10.80% for bleaching. The highest crystallinity value was obtained through bleaching, by removing amorphous components like lignin and hemicellulose. The alkaline pretreatment yielded stronger films (maximum stress of 8.8 MPa, Young’s modulus of 331.3 MPa) owing to the retained lignin and the hemicellulose reinforcing the material. This study contributes to the field of sustainable development by converting residues into valuable materials and by advancing the circular economy. The films’ specific properties make them suitable for applications like sustainable packaging, addressing environmental and industrial challenges.
23 January 2026 in Journal of Applied Polymer Science
This study introduces cellulose films enriched with vitamin A/E liposomes as sustainable, bioactive dressings for tattoo aftercare. Morphological analysis showed a smoother, more continuous microtexture than the neat cellulose films, while x‐ray diffraction indicated reduced crystallinity upon liposome incorporation. Optically, the liposome–cellulose films combined strong ultraviolet shielding across 300–400 nm with visible transparency. Time‐resolved contact‐angle measurements placed them between neat cellulose and polyurethane, indicating controlled fluid uptake consistent with a moist, non‐occlusive interface. Thermogravimetry revealed a higher peak degradation temperature with only a minimal change in onset. In uniaxial tension, the films reached a peak modulus of 16 GPa and maximum strength of 290 MPa at 50°C temperature, approaching high‐performance nanocellulose benchmarks. Together, these results show that liposome–cellulose films integrate UV shielding, tunable wettability, and enhanced thermal‐mechanical response, advancing a bio‐based alternative to conventional dressings for newly tattooed skin.
Combining high water affinity and strong UV–vis shielding while preserving mechanical performance in fully biobased cellulose films remains challenging, as hydrophilic polysaccharide modifiers and polyphenolic additives can disrupt network cohesion, promote phase-enriched domains, and trigger early fracture. Here, renewable hydrogel films were engineered from bleached Eucalyptus cellulose by incorporating sodium alginate (SA) and quercetin (Q) as multifunctional additives to tune structure–property relationships. Composite hydrogels were homogenized under a standardized and scalable protocol and converted into continuous films by doctor blade coating. Film morphology, intermolecular interactions, crystallinity, optical response, wetting and hydration, and tensile behavior were assessed by FE-SEM, ATR-FTIR, XRD, UV–vis spectroscopy, contact-angle kinetics, gravimetric water uptake, and tensile testing. Quercetin governed the visible color shift and enabled strong UV–vis attenuation (>95%), whereas alginate improved film continuity and enhanced hydration. FTIR and XRD supported predominantly noncovalent incorporation, consistent with a physically cross-linked polysaccharide network. An optimum formulation, CEL-2SA-1Q (97/2/1 wt %), delivered the highest mechanical performance (F max = 147.85 ± 9.82 N, UTS = 67.20 ± 4.46 MPa, and Young’s modulus = 1411.3 ± 18.3 MPa), corresponding to ∼1.5× higher F max and UTS and 2.75× higher modulus than neat cellulose films. The same formulation showed enhanced hydrophilicity, with the contact angle decreasing to ∼35° within 60 s and a 24 h water uptake about 3-fold higher than neat cellulose. These combined attributes suggest the potential of the optimum film as a prospective fully biobased, high-absorbency, UV–vis-opaque liner for sustainable packaging of high-moisture, light-sensitive products, where exudate retention and photoprotection are critical for preserving appearance and delaying oxidation.
Pectin films are promising renewable materials for biodegradable coatings; however, their high hydrophilicity and limited resistance to ultraviolet (UV) radiation restrict practical applications. This work investigated the influence of kraft lignin (0–5 wt%) on the structure–property relationships of grape-derived pectin films before and after accelerated UV exposure. Structural organization (XRD and FTIR), photostability (CIELAB colorimetry and CIE chromaticity), wettability, water-vapor absorption, surface morphology, soil-burial disintegration, and integrated multifunctional performance were evaluated. Lignin improved resistance to UV-induced structural changes, reducing the relative loss of apparent crystallinity from 52.76% for neat pectin to less than 7% for films containing at least 0.1 wt% lignin, while substantially decreasing UV-induced color changes. Increasing lignin content also reduced surface wettability, water-vapor uptake, and soil-burial mass loss; nevertheless, all formulations exhibited more than 50% mass loss after 120 h of soil burial. Exploratory CRITIC–TOPSIS analysis identified Pec/Lig1 as the highest-performing formulation, whereas Pec/Lig0.1 provided the most compositionally efficient balance among photostability, moisture resistance, structural stability, soil-burial disintegration, and lignin consumption. These findings demonstrate that lignin governs the trade-offs among structural stability, photostability, moisture resistance, soil-burial disintegration, and additive consumption, establishing composition–structure–property–durability relationships that provide practical design guidance for candidate functional coatings for cellulose- and paper-based substrates.
Sustainable lightweight materials based on renewable resources have attracted increasing attention as alternatives to synthetic materials. However, developing nanocellulose cryogels with adequate structural integrity and efficient retention of phenolic compounds remains challenging, often requiring furanic and dialdehyde-based additives associated with environmental and health concerns. In this context, tannin-containing nanocellulose cryogels were produced using vanillin and hydrogen peroxide as sustainable modification agents. The effects of the additives on the structural, morphological, colorimetric, mechanical, thermal, and leaching properties of the cryogels were investigated. FTIR and colorimetric analyses revealed the presence of phenolics and the effect of hydrogen peroxide. SEM analysis showed that tannin promoted structural densification, whereas peroxide induced fragmentation of the cryogel network and pore reorganization. These changes influenced density and mechanical performance, with nanocellulose-tannin exhibiting the highest compressive strength and elastic modulus. Thermal conductivity values remained within the range reported for highly porous lignocellulosic materials (38.93–43.79 (mW/m·K)). Tannin leaching demonstrated that peroxide significantly improved tannin retention, especially in the system including vanillin which exhibited only 13,61% tannin release. Overall, vanillin and hydrogen peroxide modified the supramolecular organization and functional properties of the cryogels, highlighting their potential as additives in porous materials for thermal insulation and adsorption applications.