Layered materials (LMs) produced by liquid phase exfoliation (LPE) can be used as building blocks for optoelectronic applications. However, when compared with mechanically exfoliated flakes, or films prepared by chemical vapor deposition (CVD), LPE-based printed optoelectronic devices are limited by mobility, defects and trap states. Here, we present a scalable fabrication technique combining CVD with LPE LMs to overcome such limitations. We use black phosphorus inks, inkjet-printed on graphene on Si/SiO2, patterned by inkjet printing based lithography, and source and drain electrodes printed with an Ag ink, to prepare photodetectors (PDs). These have an external responsivity (Rext)∼337 A W−1 at 488 nm, and operate from visible (∼488 nm) to short-wave infrared (∼2.7 µm, R 48 mA W−1). We also use this approach to fabricate flexible PDs on polyester fabric, one of the most common used in textiles, achieving R 6 mA W−1 at 488 nm for an operating voltage of 1 V. Thus, our combination of scalable CVD and LPE techniques via inkjet printing is promising for wearable and flexible applications.
20 January 2025 in ACS Applied Materials & Interfaces
Paper is an ideal platform for creating flexible and eco-friendly electronic systems. Leveraging the synergistic integration of zero- and two-dimensional materials, it unfolds a broad spectrum of applications within the realm of the Internet of Things (IoT), spanning from wearable electronics to smart packaging solutions. However, for paper without a polymer coating, the rough and porous nature presents significant challenges as a substrate for electronics, and the absence of well-established fabrication methods further hinders its application in wearable electronics. In this study, we present photodetectors (PDs) on a paper substrate composed of graphene and CsPbBr3 perovskite quantum dots (PQDs). Hybrid structures that combine PQDs with graphene offer a promising approach for PDs. These structures benefit from robust quantum confinement in PQDs alongside improved light interaction, tunable spectra, high absorption coefficients, and an enhanced photoconductive gain mechanism in graphene, all at ambient conditions. We use a microplotter for the lithographic printing of graphene, silver electrodes, and PQDs, to fabricate PDs on paper. These PDs have an external responsivity of ∼82,000 AW-1 at 520 nm for an operating voltage ⩽1 V. The external responsivity is 3 orders of magnitude higher than state-of-the-art paper-based PDs. Under bending at L0/L = 1.15 (L0 is the arc length and L is the chord length) and after 600 bending cycles, the external responsivity is maintained up to 80%. Thus, the combination of zero- and two-dimensional materials via microplotting on a paper substrate shows promise for wearable and flexible applications.
Paper is an ideal substrate for the development of flexible and environmentally sustainable ubiquitous electronic systems. When combined with nanomaterial-based devices, it can be harnessed for various Internet-of-Things applications, ranging from wearable electronics to smart packaging. However, paper remains a challenging substrate for electronics due to its rough and porous nature. In addition, the absence of established fabrication methods is impeding its utilization in wearable applications. Unlike other paper-based electronics with added layers, in this study, we present a scalable spray-lithography on a commercial paper substrate. We present a non-vacuum spray-lithography of chemical vapor deposition (CVD) single-layer graphene (SLG), carbon nanotubes (CNTs) and perovskite quantum dots (QDs) on a paper substrate. This approach combines the advantages of two large-area techniques: CVD and spray-coating. The first technique allows for the growth of SLG, while the second enables the spray coating of a mask to pattern CVD SLG, electrodes (CNTs), and photoactive (QDs) layers. We harness the advantages of perovskite QDs in photodetection, leveraging their strong absorption coefficients. Integrating them with the graphene enhances the photoconductive gain mechanism, leading to high external responsivity. The presented device shows high external responsivity of ∼520 A W−1 at 405 nm at <1 V bias due to the photoconductive gain mechanism. The prepared paper-based photodetectors (PDs) achieve an external responsivity of 520 A W−1 under 405 nm illumination at <1 V operating voltage. To the best of our knowledge, our devices have the highest external responsivity among paper-based PDs. By fabricating arrays of PDs on a paper substrate in the air, this work highlights the potential of this scalable approach for enabling ubiquitous electronics on paper.
The growing challenge of electronic waste drives demand for sustainable, biocompatible technologies and accelerates interest in edible electronics, systems that are safe for ingestion, biodegradable, and environmentally benign. Yet, the absence of mechanically reliable, healthy, and fully edible substrates compatible with scalable fabrication remains a major bottleneck. Here, we present a mechanically stable, fully edible substrate fabricated from wheat bran and algae via compression moulding, whose surface is further modified with chitosan spray coating to enhance water resistance and provide a uniform, coating‐compatible interface for subsequent deposition of functional inks. The substrate exhibits an ultimate tensile strength of ∼2.44 MPa, providing a stable platform for device integration. Subsequently, we develop a food‐grade conductive ink based on activated carbon and gummy bear binder, enabling uniform spray‐coated films with sheet resistance (7.6 kΩ/sq at 10 layers ∼67 µm) and linear Ohmic I–V characteristics. Moreover, electrochemical impedance spectroscopy reveals near‐ideal capacitive behaviour, with phase angle measurements across the 10 3 –10 6 Hz frequency range and Nyquist plots confirming the suitability of the system for energy storage applications. This scalable approach establishes a versatile route toward fully edible electronic platforms, opening opportunities for safe, low‐cost devices in diagnostics, smart packaging, and sustainable IoT applications.
25 September 2026 in ACS Applied Electronic Materials
All-inorganic cesium lead bromide (CsPbBr3) nanocrystals (NCs) have recently attracted extensive attention due to their high photoluminescence quantum yield (PLQY), tunable bandgap, and promising applications in photodetectors. However, the stability of photodetector devices is still limited by the defect states, lattice microstrain, and phase instability. In this work, we investigate the effects of A-site cation doping (K+, Rb+, and FA+) on the structural, optical, and photodetection properties of CsPbBr3 NCs, leading to stable photodetectors. By combining the Williamson–Hall method and DFT calculations, it has been confirmed that moderate A-site doping can preserve the cubic perovskite phase while inducing slight lattice contraction, reducing dislocation density, and enhancing crystallinity. As a result, the microstrain of 5% Rb+-doped (nominal precursor concentrations) CsPbBr3 lattice is stable around 0.0028, while its PLQY increases to 98.7% (solution) and the slow-decay lifetime extends to 81.65 ns. The photodetector devices based on doped CsPbBr3 NCs exhibit enhanced responsivity around 6.99 A/W at a high incident power of 28.1 mW, and the detectivity is stabilized around 4.9 × 1010 Jones at the light intensity from 5.6 to 22.5 mW. These findings provide clear evidence that rational A-site cation engineering is an effective strategy to optimize the optoelectronic performance of CsPbBr3 NCs for high-performance photodetectors.