25 September 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Silicon carbide (SiC) devices have the advantage of high switching speed. However, the switching speed is limited by the high parasitic inductance which could cause high voltage overshoot, parasitic turn-on, oscillation and EMI issues. Thus, the parasitic inductance of the SiC power module has to be reduced for a better performance. This paper proposed an integrated half-bridge (HB) power module based on a DBC-stacked hybrid packaging structure. This packaging structure utilizes two direct bonding copper (DBC) substrate to stack together, which forms a three-dimensional (3D) power commutation loop. The SiC chips are embedded on the top of the bottom DBC substrate to reduce the thermal resistance. Based on an optimized mutual inductance cancellation design, the proposed DBC-stacked hybrid packaging structure has only 1.8 nH commutation power loop inductance for a 1200 V, 120 A half-bridge power module. Moreover, the geometrical parameters of the laminated power terminal have been analyzed and optimized for symmetrical current sharing in the multi-chip paralleled power module. A compact 1200 V, 120 A full SiC HB power module with integrated decoupling capacitors has been fabricated, and the DC-link capacitor board, gate drivers can be integrated on the power module compactly. Finally, the static and dynamic characteristics of the proposed module have been tested. The results of double pulse test under zero external driver resistor indicate that the voltage overshoot of the proposed module is reduced by approximately 55% compared to the commercial power module, and the total switching energy is only 43% of the commercial module. Moreover, the loss of the 5.5 kW single-phase inverter based on the proposed module is reduced by 28.3% compared with the inverter based on the commercial module under 120 kHz switching frequency.
11 January 2021 in IEEE Transactions on Power Electronics
Traditional SiC MOSFET switching models cannot predict the turn-off losses precisely in the condition of small driver resistance and small load current, because they have not considered a special case in which the SiC MOSFET closes its channel before the SiC diode turns into the freewheeling-state during turn-off transient. To solve this problem, this article presents an improved SiC MOSFET turn-off model that considers the special case. The parasitic elements of circuit and the nonlinear characteristics of SiC MOSFET are also included in the proposed model to improve its accuracy. Experimental results show that the improved model can predict the turn-off transient of SiC MOSFET precisely. Moreover, the investigation of turn-off behavior shows that SiC MOSFET can achieve ultralow turn-off loss in the special case, because the channel current of SiC MOSFET can fall to 0 before the drain-source voltage rises to a high value. Driver resistance and load current are the decisive factors of achieving the special case, and this article gives the criterion of them. Besides, further studies show that lower common-source inductance, larger drain-source capacitance of MOSFET, and larger capacitance of diode can help to achieve ultralow turn-off loss. Experiments are carried out and the experimental results verify the analysis results.
21 August 2023 in IEEE Transactions on Power Electronics
The high switching speeds of Wide BandGap (WBG) devices promise further breakthroughs in the development of power modules. However, parasitic parameters bring more adverse effects at high-speed switching conditions, which makes WBG bring more power loss and ElectroMagnetic Interference (EMI) problems. In this paper, a 1200V/24A SiC half-bridge power module is presented with ultra-low parasitic capacitance and inductance for low CM EMI and low power loss. This module is designed from a stacked substrate hybrid package structure by optimizing the layout pattern. The effects of parasitic capacitance on the switching loss and conducted EMI of SiC devices are comprehensively investigated based on the analysis models. And the parasitic capacitance reduction methods and the trade-off optimization for geometrical parameters are given accordingly. The power module's layout is designed, optimized, and fabricated based on the analysis results. The proposed SiC half-bridge module reduces CM current by 17 dB and total switching loss by 28.5% compared to discrete devices. Experimental results validate the superior performance of the optimized module.
27 October 2022 in IEEE Transactions on Power Electronics
For gallium nitride (GaN) based triangular current mode (TCM) applications, the dead-time has a significant effect on the switching loss. However, previous GaN high electron mobility transistor (HEMT) models focus on the turn- on/off process without fully considering the effect of the dead-time. Hence, this article analyzes the switching transients under the superfluous and insufficient dead-time and evaluates the dead-time loss with an improved GaN HEMT model. The proposed model improves an existing GaN HEMT model by adding the voltage rising/falling time of the gate driver, the dynamic threshold voltage of Schottky-type GaN HEMTs, and an equivalent gate-drain capacitance obtained from the datasheet. Verified by a GaN-based double-pulse test, the proposed model can more accurately calculate the gate-source voltage and the self-commutated reverse conduction voltage. Verified by a GaN-based TCM Buck converter, the proposed model can predict the dead-time loss well and has higher simulation accuracy for the turn- on process induced by the inappropriate dead-time.
16 September 2021 in IEEE Transactions on Power Electronics
Benefited from the fast switching speed, Gallium nitride (GaN) high electron mobility transistors (HEMTs) have been widely used in high switching frequency converters. However, due to the significant correlation between the turn- off time and operating conditions (more than 20 times difference of the turn- off time between the high load current and small load current for GaN HEMTs), using a fixed dead time will introduce extra dead-time (DT) losses in inverters where the output voltage and current are constantly varying. Therefore, this article proposes a high-efficiency adaptive method to dynamically adjust the GaN-inverter DT with operating conditions. An improved transient model including the parasitic inductance and output voltage with bidirectional solution flow has been proposed for GaN HEMTs to increase the accuracy of DT adjustment. Based on this model, the dynamic DT adjustment can be realized without extra sensors for GaN-inverters. Using the dynamic DT adjustment, the experimental results show a peak efficiency of 98.25% in a 1200 W inverter with triangular current mode modulation. Compared with using the fixed DT, the dynamic DT method can reduce the power loss by 26.7% under full load and 49.14% under light load.
1 September 2021 in Solar Energy