9 September 2020 in IEEE Communications Letters
Traditional beam tracking has severe performance loss under the high mobility and narrow beam scenario. To alleviate the tracking performance degradation, we propose an adaptive beamwidth control for millimeter wave beam tracking. Using the particle filter, we perform the beam tracking, i.e., which is to estimate the channel gain and the angle-of-arrival (AoA). Based on the updated estimate standard deviation of AoA, the adequate beamwidth is set via the partial activation of the antenna array. Simulation results show that the beam tracking with the proposed beamwidth control maintains a higher received signal-to-noise ratio (SNR) than that of the beam tracking without the beamwidth control while the SNR gain leads to a smaller AoA tracking error under high mobility.
31 March 2022 in IEEE Wireless Communications Letters
In this letter, we propose a machine learning-based vision-aided beam selection (ML-VBS) for millimeter-wave indoor multi-user communications. The proposed scheme is aimed at addressing the beam selection overhead with narrow beams in a multi-user scenario. The proposed scheme relies on a base station (BS) equipped with a single camera to observe the scene and estimates the angles to the multiple users. Given the estimated angle information and the limited number of radio frequency chains at the BS, two serial deep neural network structures are employed for joint user and beam selection subject to a minimum rate constraint. The numerical evaluation shows that the proposed ML-VBS scheme achieves a good performance in terms of the multi-user angle estimation, achievable sum rate and low computational complexity compared to conventional beam selection techniques.
29 August 2022 in IEEE Transactions on Wireless Communications
In this paper, we present a beam tracking algorithm based on the deep Q-network (DQN) for mobile millimeter-wave (mmWave) communications. The proposed algorithm determines the receive beam angle from the received signals without knowing the channel model and dynamics. It uses the received signals of the current and previous time slots to design the state and reward of the DQN. Our goal is to maximize the signal-to-noise ratio by the actions of the designed DQN. A significant computational complexity reduction is achieved since the receiver does not need to run complicated signal processing algorithms once the DQN is properly trained. Therefore a practical implementation of mmWave beam tracking with a very large number of antennas under harsh mobile environments becomes feasible. Through the extensive simulations, we verified the performance of the proposed algorithm and demonstrated robustness to the system uncertainty and low computational complexity in comparison with particle filter and the Q-learning.
7 October 2020 in IEEE Access
Beamspace multiple-input multiple-output (MIMO) systems employ beam selection algorithms based on the sparsity of the beamspace channel to reduce the number of radio-frequency chains required in multi-user systems. In this article, we address the problem of selecting multiple beams to each user. Specifically, we propose a beam selection scheme subject to signal to interference plus noise ratio (SINR) maximization. The proposed beamspace beam selection algorithm is developed in two stages. In the first stage, each user is assigned a non-overlapping beam determined by Kuhn-Munkres assignment algorithm. In the second stage, the selected beams in the previous stage are augmented with additional beams from an $M$ -dominant beam set subject to a sum-rate maximization criterion. The performance of the proposed scheme is verified by simulations, and the results show a near-optimal performance in terms of the achievable sum-rate. Also, a significant improvement in terms of energy efficiency is achieved compared to the conventional beam selection scheme.
6 October 2020 in IEEE Communications Letters
27 January 2025 in IEEE Transactions on Wireless Communications
In this paper, we propose a two-dimensional signal path classification (2D-SPC) for reconfigurable intelligent surface (RIS)-assisted near-field (NF) localization. In the NF regime, multiple RIS-driven signal paths (SPs) can contribute to precise localization if these are decomposable and the reflected locations on the RIS are known, referred to as SP decomposition (SPD) and SP labeling (SPL), respectively. To this end, each RIS element modulates the incoming SP’s phase by shifting it by one of the values in the phase shift profile (PSP) lists satisfying resolution requirements. By interworking with a conventional orthogonal frequency division multiplexing (OFDM) waveform, the user equipment can construct a 2D spectrum map that couples each SP’s time-of-arrival (ToA) and PSP. Then, we design SPL by mapping the SPs with the corresponding reflected RIS elements when they share the same PSP. Given two unlabeled SPs, we derive a geometric discriminant by checking whether the current label is correct. It can be extended to more than three SPs by sorting them using pairwise geometric discriminants between adjacent ones. From simulation results, it has been demonstrated that the proposed 2D-SPC achieves consistent localization accuracy while poor accuracy in a benchmark, even if insufficient PSPs are given.