Petro Leontiev

Petro Leontiev

Auto-generated profile, based on publicly available information

Petro Leontiev

Sumy State University, Ukraine

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 April 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
HKHeorhii Kulinchenko
Heorhii Kulinchenko
VZViacheslav Zhurba
Viacheslav Zhurba
APAndrii Panych
Andrii Panych
PLPetro Leontiev
Petro Leontiev
The study is devoted to the expander turbine rotation speed regulator, considering the possibility of implementing this regulator on microprocessor automation tools. The use of expander-generator units in general improves energy saving indicators, and the ability to maintain the turbine shaft rotation speed within the specified limits, in turn, directly affects the indicators of the quality of the generated electricity. The expander turbine, as a control object, is described by non-linear equations, which determines the possibility of using regulators of different designs, and requires the selection of the most suitable one according to certain criteria. As part of the study, based on the tasks of practical implementation of the regulator on microprocessor devices, the expediency of reducing the transfer function of the model in the process of identifying the control object was confirmed. As a result of research on an experimental setup, it is shown that the use of a three-position relay regulator allows for regulation dynamics at the level of a classic PID regulator. An important result of the research is the stabilization of the turbine rotation speed, which affects the parameters of the electricity generated by the generator. The description of the control object was linearized by constructing a family of transfer functions for the operating points of the control range. For the construction of the turbine rotation speed regulator, the criterion of "minimum fluctuation of the parameter when changing its set value" is proposed. A regulator for a non-linear object with oscillatory features is built, which has a simple implementation and a cycle time of 1 ms. It makes it possible to reduce rotation speed fluctuations to 5 % and minimize the impact of rotation process disturbances

30 June 2022 in ScienceRise
Verified
Journal Article
Open access
PDF file
HKHeorhіi Kulіnchenko
Heorhіi Kulіnchenko
APAndrii Panych
Andrii Panych
PLPetro Leontiev
Petro Leontiev
VZViacheslav Zhurba
Viacheslav Zhurba
The object of research: The expander of the excess gas pressure utilization plant. Investigated problem: Increasing the efficiency of the process of utilization of excess gas pressure during its distribution from main high-pressure gas pipelines. Development of hardware and software tools that provide automation of the process of regulating flow parameters under the influence of time-varying disturbances. The main scientific results: A mathematical model of the process of utilization of excess gas pressure has been developed, and an experimental assessment of its adequacy has been carried out. With the help of the Matlab application “Linear Analysis Points”, the description of the object is linearized, which makes it possible to obtain its representation in the state space. The area of practical use of the research results: The sphere of application of the results of the study is automation objects related to the regulation of gas flow parameters. The results of identification of model parameters provide an opportunity for the synthesis of the process controller. Innovative technological product: In accordance with the task of increasing the efficiency of the process of utilization of excess gas pressure when it is distributed from the main high-pressure gas pipelines, a mathematical model of the channel for controlling the speed of rotation of the turbine (expander) has been developed, which serves as the basis for the synthesis of the regulator for the utilization process. Scope of the innovative technological product: The developed model can be used in the construction of turbine speed controllers, which are used in the generation of electricity. The approach to the linearization of the description of the control object makes it possible to automate the process of identifying its parameters.

14 December 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
IDIvan Dehtiarov
Ivan Dehtiarov
PLPetro Leontiev
Petro Leontiev
DMDmytro Miroshnychenko
Dmytro Miroshnychenko
VLVadym Lanchynskyi
Vadym Lanchynskyi
PBPavlo Buhaiets
Pavlo Buhaiets
During hostilities, ground robotic systems play an important role in minimizing losses of servicemen and suspending the combat capabilities of troops. For firing, robotic complexes are equipped with gun turrets. Researchers are conducting research to improve the performance, reliability and firing accuracy of such turrets. This work describes the design and research of an experimental sample of a ground robotic system, which is equipped with a turret for controlling the position of a machine gun. The description and results of experimental studies of dynamic loads during robot movement at different speeds and road conditions are presented. It was established that the values of the maximum accelerations that must be worked out by the stabilization system during operation for the experimental design of the robot do not exceed 20 rad/s2. The possibility of using counterweights was considered to reduce the torque of the turret guidance drive while reducing the dimensions of the robotic system structure. The description of the experimental module equipped with a control and measurement system and the results of experimental studies on determining the power of the turret drives during the manipulation of the structure are presented. A procedure of dynamic analysis and the results of modeling the movement of the gun turret in the ANSYS software package are presented. The proposed method for designing the structure ensures the determination of the impact on the structure of the complex shape of loads caused by its manipulation, to compensate for the exciting loads when the robotic system is moved over the terrain. With the help of this method, it is possible to determine and minimize the power, and therefore the energy consumption, of azimuth and lifting electric drives at the design stage

30 April 2021 in ScienceRise
Verified
Journal Article
Open access
PDF file
HKHeorhіi Kulіnchenko
Heorhіi Kulіnchenko
PLPetro Leontiev
Petro Leontiev
ODOleksii Drozdenko
Oleksii Drozdenko
Object of study: Automation of control of technological parameters of the process of low-temperature separation (LTS) of moisture from a gas stream. Investigated problem: Improving the efficiency of the separation process when preparing gas for transportation through the consumption network. Development of hardware and software tools that provide automation of the process of regulating flow parameters under conditions of action of time-varying disturbances. Main scientific results: A criterion for controlling the LTS process of a gas flow is formulated. The difference in the dynamic characteristics of the processes occurring during the separation of moisture makes it possible to effectively use a two-circuit control system. The perspective of using extreme regulators (ER) of the process, which is characterized by time delays between the input of the object and its output, is substantiated. The use of ER ensures the stability of the control process under the influence of disturbances in the parameters of the gas flow. In the MATLAB environment, an ER model has been developed, in which a step-type algorithm is used, which provides an increase in the efficiency of the LTS process in accordance with the selected criterion The area of practical use of research results: The scope of use of the research results are automation objects that need continuous automatic tracking of the changing settings of the process parameters regulators. The studies carried out make it possible to use the proposed regulator in various technological installations for drying gas and air (with appropriate identification of the parameters of the object). Innovative technological product: Based on the formed criterion for controlling the LTS process, which is aimed at increasing the efficiency of the LTS process of moisture from a gas flow, a microprocessor-based step-type ER has been developed. Preliminary tests of the regulator show that it can be implemented on commercially available program logic controllers on the market. Scope of application of an innovative technological product: The considered ER can be used to construct control systems for oil and gas transportation processes, which require adaptation and optimization modes to flow parameters. In this case, the need for adaptation is dictated by changes in flow parameters over time.

1 February 2026
Verified
Book Chapter
Closed access
OSOleksandr Sokolov
Oleksandr Sokolov
JPJán Piteľ
Ján Piteľ
AIAngelina Iakovets
Angelina Iakovets
SSSerhii Sokolov
Serhii Sokolov
PLPetro Leontiev
Petro Leontiev

8 September 2022 in Information Technology: Computer Science, Software Engineering and Cyber Security
Verified
Journal Article
Closed access
PDF file
ГКГеоргій Кулінченко
Георгій Кулінченко
ПЛПетро Леонтьєв
Петро Леонтьєв
АПАндрій Панич
Андрій Панич
АСАрсен Савенко
Арсен Савенко
Метою роботи є отримання необхідних даних для розробки системи підйому платформи стріли будівельного 3D-принтера, що дозволить підвищити точність позиціювання за рахунок оптимізації режимів роботи обладнання. Реалізація поставленої мети передбачає вирішення завдань: розробки математичної моделі електромеханічного перетворювача, що забезпечує точне переміщення платформи стріли будівельного 3D-принтеру на базі вибраної електричної машини; дослідження взаємозв’язку конструктивно- технологічних параметрів системи підйому; формування засад побудови схеми керування електроприводом та гідроприводом, що забезпечує утримання заданої позиції в підйомних гідроприводах. Методологія вирішення поставленого завдання полягає в імітаційному моделюванні процесу переміщення гідроприводів платформи завдяки зміни тиску в гідравлічній системі за допомогою насосу і крокового двигуна в якості приводу. Використані методи теорії автоматичного керування електричними апаратами, перетворень Лапласа, методи теорії електроприводу, електричного та магнітного поля, теорії гідромеханіки і математичного моделювання. Наукова новизна. В ході виконання роботи створено методику побудови електроприводу системи підйому платформи будівельного 3D-принтеру і отримання характеристик приводу на основі крокового двигуна в середовищі Matlab/Simulink. Висновки. Основним результатом досліджень є підвищення точності позиціонування висоти платформи стріли будівельного 3D-принтера завдяки опрацюванню режимів роботи крокового двигуна у складі електроприводу гідравлічної системи підйому. Розроблена модель каналу керування позиціонуванням стріли будівельного 3D-принтера, досліджені алгоритми керування кроковим двигуном по зміні витрат робочого середовища, продуктивність і точність під час позиціювання платформи стріли. Модель дозволяє впровадити запропоновані методи моделювання для інших контурів керування об’єктом.