Mohd Shihabudin Ismail

Mohd Shihabudin Ismail

Auto-generated profile, based on publicly available information

Mohd Shihabudin Ismail

Faculty of Mechanical Engineering and Technology, Universiti Malaysia Perlis (UniMAP), Perlis, Malaysia

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 May 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
YXYeo Yi Xuan
Yeo Yi Xuan
MRM.J.M. Ridzuan
M.J.M. Ridzuan
MMM.S. Abdul Majid
M.S. Abdul Majid
MRM.T.A. Rahman
M.T.A. Rahman
FYFerriawan Yudhanto
Ferriawan Yudhanto
MIMohd Shihabudin Ismail
Mohd Shihabudin Ismail

10 May 2024 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
MAM. A. A. Ahmad
M. A. A. Ahmad
RMRidzuan M.J.M.
Ridzuan M.J.M.
MMM.S. Abdul Majid
M.S. Abdul Majid
Mohd Sapuan SalitMohd Sapuan Salit
Mohd Sapuan Salit
MIMohd Shihabudin Ismail
Mohd Shihabudin Ismail
SBShahriman Abu Bakar
Shahriman Abu Bakar

31 March 2024 in Journal of Advanced Research in Applied Mechanics
Verified
Journal Article
Open access
PDF file
YXYeo Yi Xuan
Yeo Yi Xuan
RMRidzuan M.J.M.
Ridzuan M.J.M.
MMM.S. Abdul Majid
M.S. Abdul Majid
MIMohd Shihabudin Ismail
Mohd Shihabudin Ismail
FYFerriawan Yudhanto
Ferriawan Yudhanto
FMFauziah Mat
Fauziah Mat
Short natural fibres replace synthetic fibres as filler in natural rubber (NR) as they are environmentally beneficial and sustainable. This study investigates the cure behaviour and tensile properties of pineapple leaf fibre (PALF) reinforced NR composites at various fibre contents. The fibre contents are varied at 0, 10, 20 and 30 parts per hundred rubber (phr). PALF reinforced NR composites are prepared using a two-roll mill. Surface morphology of tensile fractured specimens is examined using scanning electron microscopy (SEM). The results demonstrated that the optimum cure time decreases significantly with greater fibre content. The hardness value increases gradually with increasing filler content. The stress-strain graphs show an increasing trend in stress at higher fibre content particularly at low strain regions. On the contrary, the tensile strength reduces when the fibre content is increased up to 30 phr. SEM analysis reveals that the fibre-matrix adhesion is considerably poor due to the fibre pullout phenomenon observed. It is indicated that higher fibre content could be possibly reinforced to NR to achieve high deformation stress at incredibly low strain regions.

1 January 2019 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
MIM. S. Ismail
M. S. Ismail
YCY. P. Chan
Y. P. Chan
MHM. I. Hussain
M. I. Hussain
NMN. Muhammad
N. Muhammad
ZZZ. Mohd Zain
Z. Mohd Zain

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
MAM. A. A. Ahmad
M. A. A. Ahmad
MRM. J. M. Ridzuan
M. J. M. Ridzuan
MMM. S. Abdul Majid
M. S. Abdul Majid
MIMohd Shihabudin Ismail
Mohd Shihabudin Ismail
ECE. M. Cheng
E. M. Cheng
In this paper, an experimental investigation is conducted to examine the electrical conductivity of glass epoxy composites containing graphene and carbon nanofi In this paper, an experimental investigation is conducted to examine the electrical conductivity of glass epoxy composites containing graphene and carbon nanofi

1 November 2023 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
MIMohd Shihabudin Ismail
Mohd Shihabudin Ismail
MIMohamad Shaiful Ashrul Ishak
Mohamad Shaiful Ashrul Ishak
NYNor Zaiazmin Yahaya
Nor Zaiazmin Yahaya
MHMuhammad Iqbal Muhammad Hussain
Muhammad Iqbal Muhammad Hussain
MRMohd Adzrie Radzali
Mohd Adzrie Radzali
Line Balancing Chart is one of the most used lean tools for determining cycle time (CT) and lead time (LT) in the production line processes flow, from raw material input until finished product output. However, for traditional Line Balancing Chart, only the average (mean) CT and LT are considered which causing inconsistent performance of the actual production line throughput rate (productivity). In this study, Variable-Line Balancing Chart (V-LBC) is introduced by considering the dynamic CT and LT in a form of (Minimum, Most Likely (mean), Maximum) for each process involved in the production line. The risk assessment for Value-added (VAA) and non-value added (NVAA) events in the flow are also considered for this V-LBC. A Monte Carlo simulation by using @Risk software is utilized to simulate each process CT distribution capability. As a result, each process in the V-LBC could be represented in horizontal and vertical time variables that involve a variable CT (VAA and NVAA) and risk assessment using Risk Assessment-Failure Mode and Effect Analysis (RA-FMEA) approach. The actual root cause led to the process variation also could be identified more accurately from the V-LBC. Hence the correct action could be taken in order to reduce the variation which indirectly increase the production line productivity.