Ingrid Khongová

Ingrid Khongová

Auto-generated profile, based on publicly available information

Ingrid Khongová

Research Institute for Building Materials

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2021 in Journal of Microscopy
Verified
Journal Article
Closed access
PDF file
TSTheodor Staněk
Theodor Staněk
MDMatej Dzurov
Matej Dzurov
IKIngrid Khongová
Ingrid Khongová
MBMartin Boháč
Martin Boháč

28 October 2021
Verified
Book Chapter
Closed access
PDF file
TSTheodor Staněk
Theodor Staněk
MKMichaela Krejčí Kotlánová
Michaela Krejčí Kotlánová
AZAnežka Zezulová
Anežka Zezulová
IKIngrid Khongová
Ingrid Khongová
MBMartin Boháč
Martin Boháč
MDMatej Dzurov
Matej Dzurov

25 March 2024 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
DJDenisa Jancarikova
Denisa Jancarikova
IKIngrid Khongova
Ingrid Khongova
PBPetr Bibora
Petr Bibora
HSHalina Szklorzova
Halina Szklorzova
Testing of the properties of cement mortars for 3D printing has not been standardized yet. Manufacturers of dry mixes declares tensile strength and compressive strength, but these properties are determined on standard beams for cement mortars, and their values may differ from the material actually formed by the 3D printing method. Another factor affecting strength is the printing process itself, where different printing machines require different consistencies and therefore different amount of water. Last but not least, it is necessary to take into account the different properties of the printed material depending on the direction of testing. Presented article brings results of determination the compressive strength, flexural tensile strength, splitting tensile strength and uniaxial tensile strength of the cement mortar from 3D printing loaded in different directions in relation to the axis of the print and comparing them with the parameters determined on standard beams made of the same material. A commercially produced dry mixture was used. Rectangular object was printed. Before the actual printing and also the fresh mixture was taken from the print head directly into the molds for the production of standard beams 40×40×160 mm. The printed object and the beams were placed in a water environment after 24 hours and the properties were determined at the age of 28 days. Cubes with dimensions of 40×40×40 mm and beams of 40×40×160 mm were subsequently cut from the printed object. The results of the testing point to a relatively large variability of the strength characteristics not only according to the direction of the load forces, but also in different places of the printed object (samples were taken in the bottom part, in the middle and in top of the printed object). Strengths of the standard beams were significantly higher than strengths of samples cut out from 3D printed object.

26 October 2021 in Journal of Microscopy
Verified
Journal Article
Closed access
PDF file
MBMartin Boháč
Martin Boháč
IKIngrid Khongová
Ingrid Khongová
AZAnežka Zezulová
Anežka Zezulová
MKMichaela Krejčí Kotlánová
Michaela Krejčí Kotlánová
DKDana Kubátová
Dana Kubátová
TSTheodor Staněk
Theodor Staněk

1 September 2022 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
IKI Khongova
I Khongova
ICI Chromkova
I Chromkova
VPV Prachar
V Prachar
The aim of this research is the maximum use of waste as a substitute for primary sources in cement mortars. In the experimental work, recycled concrete and waste mineral fibers were used to substitute the filler. Effects of different aggregate replacement ratios (5, 15, and 25%) on the resulting mortar properties were investigated. The application of waste materials resulted in a decrease in compressive and tensile strengths; on the contrary, a very favorable effect was recorded when monitoring the thermal insulation properties and frost resistance. The results of experimental work have shown that the waste materials used can be a full-fledged alternative to natural aggregates.

1 June 2024
Verified
Book Chapter
Closed access
PDF file
TSTheodor Staněk
Theodor Staněk
EBEva Bartoníčková
Eva Bartoníčková
IKIngrid Khongová
Ingrid Khongová
AZAnežka Zezulová
Anežka Zezulová
JPJakub Palovčík
Jakub Palovčík
MBMartin Boháč
Martin Boháč