Dielectric polymer nanocomposites are considered as one of the most promising insulation material candidates for future capacitive energy storage applications, providing tailorability of charge trapping and transport properties at the nanometric level which is a key for increased dielectric performance of biaxially oriented polypropylene (BOPP) for metallized film capacitors in high-voltage direct current (HVDC) applications. In this study, a comprehensive investigation of morphology and dielectric performance of pilot-scale BOPP nanocomposites with hexamethyldisilazane (HMDS)-treated hydrophobic fumed silica nanoparticles was carried out, providing critical perspectives on the performance and challenges of PNCs for thin film capacitors also in a broader context. In non-oriented cast films, incorporation of nanosilica modified the crystallization kinetics and α/β-crystalline spherulitic morphology of polypropylene and reduced the accumulation of space charge under a DC electric field. The nanocomposites exhibited promising dispersion characteristics in the nano-scale, however, the low amount of micron-sized agglomerates inherently present in commercial fumed silica persisted in the compounds which can become critical for thin film applications. Subsequently, biaxial-stretching-induced morphology development and dielectric properties of silica-BOPP nanocomposites were evaluated, highlighting the role of precursor morphology and film processing in the silica-BOPP film morphology, defects and dielectric performance. Charge trapping and transport properties of silica-BOPP films were investigated by isothermal and thermally stimulated techniques under high DC electro-thermal stresses, indicating profound modification of the trap density of states brought about by nanosilica. This resulted in more homogeneous space charge distribution and reduced temperature- and field dependent DC conductivity at 100 °C in comparison to neat BOPP under moderate field stresses (<200 V μm−1), while simultaneously maintaining low dielectric loss. However, the localized weak points caused by silica agglomerates still remain a challenge for the structural homogeneity and dielectric breakdown performance of thin BOPP films under extreme-field stress, hence emphasizing the need for further advancements in the agglomerate and PNC film morphology control to provide high-reliability nanodielectric capacitor thin films for practical HVDC film capacitor applications.
13 July 2018 in IEEE Transactions on Dielectrics and Electrical Insulation
Breakdown strength, DC resistivity, permittivity and loss of thermally sprayed alumina coatings were studied at various temperatures and relative humidities. The studied coatings were sprayed by utilizing three different spray techniques: flame, high-velocity oxygen fuel (HVOF) and plasma spraying. Breakdown behavior of HVOF sprayed alumina were studied up to very high temperatures (800 °C). At 20-180°C, no significant trend could be seen in the breakdown strength of HVOF and plasma sprayed alumina coatings. The breakdown strength of alumina coatings decreased gradually from 300 to 800 °C reaching a value which was only 14% of the breakdown strength measured at 20 °C/RH 20%. Increasing humidity (from 20 to 90%) decreased the DC resistivity of the alumina coatings five orders of magnitude. Correspondingly, permittivity and losses increased with the humidity; in most cases with a notable contribution due to DC conduction. The material behavior may be linked to the microstructure of coatings consisting of amorphous and crystalline regions with interfaces in between. Moreover, the alumina coatings exhibited notable amount of highly hygroscopic γ-phase which also affected the moisture sensitivity of the coatings.
1 January 2015 in Journal of Thermal Spray Technology
This study compares different polymer-nanofiller blends concerning their suitability for application as insulating thermoplastic composites for High Voltage Direct Current (HVDC) cable application. Two polymer blends, PP/EOC (polypropylene/ethylene-octene copolymer) and PP/PP-HI (polypropylene/ propylene - ethylene copolymer) and their nanocomposites filled with 2 wt.% of fumed silica modified with 3-aminopropyltriethoxysilane were studied. Morphology, thermal stability, crystallization behavior dynamic relaxation, conductivity, charge trap distribution and space charge behavior were studied respectively. The results showed that the comprehensive performance of the PP/PP-HI composite is better than the one of the PP/EOC composite due to better polymer miscibility and flexibility, as well as lower charging current density and space charge accumulation. Nanosilica addition improves the thermal stability and dielectric properties of both polymer blends. The filler acts as nucleating agent increasing the crystallization temperature, but decreasing the degree of crystallinity. Dynamic mechanical analysis results revealed three polymer relaxation transitions: PP glass transition (β), weak crystal reorientation (α1) and melting (α2). The nanosilica introduced deep traps in the polymer blends and suppressed space charge accumulation, but slightly increased the conductivity. A hypothesis for the correlation of charge trap distribution and polymer chain transition peaks is developed: In unfilled PP/EOC and PP/PP-HI matrices, charges are mostly located at the crystalline-amorphous interface, whereas in the filled PP/EOC/silica and PP/PP-HI /silica composites, charges are mostly located at the nanosilica-polymer interface. Overall, the PP/PP-HI (55/45) nanocomposite with 2 wt.% modified silica and 0.3 wt.% of antioxidants making it a promising material for PP based HVDC cable insulation application with a reduced space charge accumulation and good mechanical properties.
7 March 2017 in IEEE Transactions on Dielectrics and Electrical Insulation
In this study, the DC conductivity from low electric fields up to breakdown fields is studied for several different thermally sprayed ceramic coatings. Although the DC conductivity of bulk alumina ceramic has been observed to follow the space charge limited current conduction mechanism, the studied ceramic coatings do not follow or follow only partly this mechanism. Possible reason for this is their different microstructure since bulk alumina exhibits fully crystalline microstructure while the ceramic coating consists of crystalline and amorphous regions as well as voids, defects and numerous interfaces. A possible conduction mechanism of the ceramic coatings based on the different conductivities of the amorphous and crystalline regions of the coatings is proposed. The microstructural features (e.g. volumetric porosity) are found to affect the breakdown strength for some of the studied coatings. The step-test breakdown strengths of the coatings were lower than the ramp-test ones due to the longer stress durations in step tests giving an indication of effects of electrical stress duration and possible short-term degradation of the coatings.
A large-area multiple breakdown measurement using self-healing gold sputtered electrodes was evaluated in determining the AC breakdown characteristics of insulating biaxially oriented polypropylene (BOPP) and BOPP-silica nanocomposite thin films. Results were compared with conventional small area measurements and it is shown that the large-area approach could be extended into AC measurements as long as good quality film-electrode interface in ensured. Special electrode arrangements are needed due to the absence of electrostatic force. AC small-area breakdown strength of pilot-scale films was ramp rate dependent but no such effect was clearly noticed for a commercial product. Conventional DC small-area breakdown measurements were also conducted and the results were compared to previously published large-area multiple breakdown data. The consistent results support the dependency between ramp rate and DC breakdown strength in the studied BOPP-silica nanocomposite.