18 February 2019 in IEEE Transactions on Power Electronics
In this paper, a phase-shifted full-bridge converter employing a new center-tapped clamp circuit is proposed to achieve high efficiency and high power density in electric-vehicle battery charger applications. By using a simple center-tapped clamp circuit, which consists of two diodes and one capacitor, many limitations in conventional PSFB converters are solved. The proposed center-tapped clamp circuit provides the clamping path and allows the secondary voltage stress to be clamped to the secondary-reflected input voltage. This results in a greatly reduced conduction loss in the secondary full-bridge rectifier (FBR) due to the low forward-voltage drop of low voltage-rated diodes, and the resistor-capacitor-diode snubber loss is eliminated. In addition, the circulating current in the primary side is removed without any duty-cycle loss. Furthermore, the turn-off switching loss in the FBR is substantially reduced due to the decreased reverse-recovery current and the reduced reverse voltage. With these advantages, high efficiency can be achieved. Besides, the size of the output inductor is considerably reduced with the aid of clamping voltage, resulting in a high power density with saving the cost. In order to confirm the effectiveness of the proposed converter, a 3.3-kW prototype was tested. Experimental results show that the proposed converter achieves high efficiency over the entire conditions with high power density.
28 July 2020 in IEEE Transactions on Power Electronics
This letter presents a new single-phase 13-level switched-capacitor inverter with a reduced number of switches and a voltage boost gain of 6. The proposed topology with a single DC source can achieve 13-level output, sextuple boost, and self-voltage balance of capacitors using only 14 switches. The proposed inverter does not use a back-end H-bridge with four switches that must withstand the peak load voltage, and the voltage stress of all switches does not exceed half of the peak load voltage. The operation principle including the self-voltage balance of capacitors is described in detail. An analysis of the proposed inverter in comparison to recent topologies with a single-input DC source is performed mainly in terms of the number of switches and cost function. Simulation and experimental results verify the feasibility of the proposed topology.
19 February 2019 in IEEE Transactions on Power Electronics
25 October 2019 in IEEE Transactions on Power Electronics
6 March 2019 in IEEE Transactions on Power Electronics
A conventional phase-shifted full-bridge (PSFB) converter is one of the most promising topologies in high efficiency and high power applications because of its small RMS current, inherent zero-voltage switching (ZVS) capability, and clamped voltage stress of the primary switches. However, when the PSFB converter operates with a small duty-ratio, a large freewheeling current of an output inductor flows in the primary side, and it causes a large circulating current. In addition, it has a large voltage stress in the rectifier diodes due to a voltage ringing between parasitic components. To solve these problems, a new PSFB converter with a coupled inductor rectifier (CIR) is proposed in this paper. By adopting the CIR structure in the PSFB converter instead of the full-bridge rectifier, the proposed converter eliminates the freewheeling current in the primary side which significantly reduces the primary circulating current. In addition, the two rectifier diodes of the CIR do not have voltage ringing. As a result, the proposed converter not only reduces the conduction loss in the primary side, it can also use two diodes in the rectifier with a low voltage rating. The effectiveness and feasibility were verified with a 320-400 V input and 56 V/12.8 A output prototype.
9 October 2017 in IEEE Transactions on Power Electronics
A new synchronous rectifier (SR) control method is proposed to improve the light-load regulation capability of high-frequency LLC resonant converter. The proposed control method applies the extended SR turn-on time, which results in the negative current flowing through SRs, and the light-load regulation of the LLC resonant converter can be achieved by the negative current. The design guideline of the extended SR turn-on time is presented based on the precise analysis and the equivalent circuit modeling of the LLC resonant converter. In addition, the switching loss and gate driving loss can be reduced because the output voltage can be regulated at low switching frequency. The validity of a proposed control method is confirmed by the experimental results of a prototype converter with 330-380 VDC input and 750 W (12 V/62.5 A) output.