Takashi Ueda

Takashi Ueda

Auto-generated profile, based on publicly available information

Takashi Ueda

Kanazawa University

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2005 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
TUTakashi Ueda
Takashi Ueda
AHAkira Hosokawa
Akira Hosokawa
KYKeiji Yamada
Keiji Yamada
In this paper, the influence of oil mist on the tool temperature in cutting is investigated experimentally. The turning of a carbon steel with oil mist applied is performed, and the temperature of the alumina tool at the tool-chip interface is measured using a two-color pyrometer. The tool temperature in dry cutting at a cutting speed of 300 m/min is ∼1060°C, but it is ∼1000°C when oil mist is supplied. In intermittent turning, the oil mist has more effect on the tool temperature because it is supplied more efficiently to the tool-chip interface. In end milling with the oil mist applied, the tool temperature at the flank face is ∼580°C at a cutting speed of 400 m/min, though in dry cutting it is ∼660°C.

19 May 2022 in CIRP Annals
Verified
Journal Article
Open access
AHAkira Hosokawa
Akira Hosokawa
KKKoki Kosugi
Koki Kosugi
TUTakashi Ueda
Takashi Ueda

1 January 2020 in CIRP Annals
Verified
Journal Article
Closed access
AHAkira Hosokawa
Akira Hosokawa
RSRyo Saito
Ryo Saito
TUTakashi Ueda
Takashi Ueda

1 January 2003 in Journal of the Japan Society for Precision Engineering
Verified
Journal Article
Open access
KYKeiji Yamada
Keiji Yamada
SNShingo Nishioka
Shingo Nishioka
AHAkira Hosokawa
Akira Hosokawa
TUTakashi Ueda
Takashi Ueda
Laser cleaving process is a prospective technique to divide a thin plate of brittle materials into small pieces, because of its high yield ratio and controllability. In addition, the process is carried out without coolant which causes the environmental pollution and the contamination of the electrical devices etched on the wafer. In this paper, laser cleaving of silicon wafer is conducted with pulsed Nd: YAG laser. The temperature of laser spot is measured by means of the two-color pyrometer with optical fiber and the acoustic emission caused by crack propagation is also observed. When the laser spot is scanned at the appropriate interval and velocity, the crack propagates in sequence by the corresponding laser irradiation. As a result, both high linearity of cleaved edge and fine fractured surface roughness are obtained. The thermal stress distribution induced by laser irradiation is analysed with FEM model, in which the stress intensity factor is calculated at the vicinity of the crack tip in order to clarify the criterion of crack propagation. The analysis and experiments reveal that the maximum tensile stress at the crack tip increases with temperature and the crack propagates when the stress intensity factor reaches the fracture toughness of the material

1 January 2013 in Journal of Advanced Mechanical Design, Systems, and Manufacturing
Verified
Journal Article
Open access
MAMohd Sanusi Abdul Aziz
Mohd Sanusi Abdul Aziz
TFTatsuaki Furumoto
Tatsuaki Furumoto
KKKazuhiro Kuriyama
Kazuhiro Kuriyama
STShigeki Takago
Shigeki Takago
SASatoshi Abe
Satoshi Abe
TUTakashi Ueda
Takashi Ueda

31 December 2011 in CIRP Annals
Verified
Journal Article
Closed access
TFTatsuaki Furumoto
Tatsuaki Furumoto
TUT. Ueda
T. Ueda
AKA. Kasai
A. Kasai
AHA. Hosokawa
A. Hosokawa