Paul T. Mead

Paul T. Mead

Auto-generated profile, based on publicly available information

Paul T. Mead

Texas A&M University

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2024 in International Journal of Impact Engineering
Verified
Journal Article
Closed access
IFIoan Feier
Ioan Feier
MAMichael Anderson
Michael Anderson
JBJames R. Boudrie
James R. Boudrie
EJErin M. Jarrett-Izzi
Erin M. Jarrett-Izzi
JGJonathon L. Gabriel
Jonathon L. Gabriel
TLThomas E. Lacy
Thomas E. Lacy

31 July 2025 in International Journal of Impact Engineering
Verified
Journal Article
Closed access
JRJacob A. Rogers
Jacob A. Rogers
KXKailu Xiao
Kailu Xiao
PMPaul T. Mead
Paul T. Mead
CPCharles U. Pittman
Charles U. Pittman
ETEdwin L. Thomas
Edwin L. Thomas
TLThomas E. Lacy
Thomas E. Lacy

15 August 2025 in Journal of Dynamic Behavior of Materials
Verified
Journal Article
Closed access
PDF file
PMP. T. Mead
P. T. Mead
JRJ. A. Rogers
J. A. Rogers
TWT. N. Williams
T. N. Williams
JWJ. W. Wilkerson
J. W. Wilkerson
TLT. E. Lacy
T. E. Lacy

9 June 2026 in engrXiv
Verified
Preprint
Open access
JRJacob A. Rogers
Jacob A. Rogers
AMAniket Mote
Aniket Mote
SDSidney Davis
Sidney Davis
PMPaul T. Mead
Paul T. Mead
CPCharles U. Pittman
Charles U. Pittman
TLThomas Lacy
Thomas Lacy
All spacecraft continue to face a growing risk of hypervelocity impact (HVI) by micrometeoroids and orbital debris (MMOD). Concurrently, emerging hypersonic weapons pose acute ballistic threats to military and civilian assets. In both cases, the diminishing effectiveness of legacy armor demands the development of specialized, layered HVI protective structures. Ultra-high molecular weight polyethylene (UHMWPE) and high-density polyethylene (HDPE) stand out as promising intermediate layers due to their high mass-specific energy absorption and tailorability. Yet, their behaviors at HVI-induced strain rates (>106 s-1) remain understudied and poorly understood, particularly near their glass transition (-116°C) and melt (130°C) temperatures. A recent HVI study revealed that, when impacted at room temperature, UHMWPE targets exhibited bulk fragmentation while similar HDPE samples showed extensive melting and visco-plastic flow, differences attributed to molecular mobility. This follow-on study probes the interplay of initial target temperature (T0), impact velocity (v0), and average entanglements per chain (Ne) on polyethylene’s (PE’s) HVI response. 12.7 mm thick UHMWPE and HDPE plates at T0 = -120°C, 20°C, and 140°C were subjected to 2.5 km/s and 6.0 km/s HVIs by 6.35 mm diameter aluminum spheres. PE’s HVI response was found to be largely governed by a competition between rates of strain and polymer chain relaxation. Lowering T0 for a fixed Ne constrained chain motion analogously to increasing Ne at a fixed T0. This caused HDPE’s HVI response to increasingly align with UHMWPE’s at similar v0. The opposite was also observed. Increasing v0 alone made both materials more prone to widespread fracture by raising strain rates beyond rates of chain disentanglement and reorientation. The material exhibiting the most visco-plastic flow without subsequent bulk fragmentation lost less mass, had smaller perforations, and better absorbed energy, suggesting that, for a given T0 and v0, there is an optimal Ne value that maximizes PE energy absorption. Increasing v0 or decreasing T0 necessitates a reduction in Ne to sustain the degree of molecular mobility that gives maximum energy absorption. These findings motivate the development of a protective structure composed of PE layers, each optimized for an anticipated average strain rate.