1 January 2020 in Fundamental and applied problems of ferrous metallurgy
The amount of residual austenite in martensitic roll steels is an important technological parameter of heat treatment, which affects the performance properties of the rolls. But determining its amount in roll steels is a complex and not fully solved scientific and technical problem. The aim of the work was to comparatively analyze the amount of residual austenite in the structure of alloy steel rolls by X-ray diffraction, ultrasonic methods and metallography analysis. However, the qualitative difference of microstructures in the content of the light phase - austenite, confirms the results of X-ray diffraction analysis. No correlation was found between the austenite content in the samples and their hardness. It was found that the X-ray method, based on the comparison of the intensities of the α- and γ-phase lines of iron, overestimates the value of the amount of residual austenite in some samples of roll steels. The results of the analysis of residual austenite by ultrasound rate showed better convergence. The amounts of residual austenite, calculated on the sample of stainless steel (100% γ-Fe), had reduced values (2.6-4.5%). The most accurate results on the amount of residual austenite gave the use of the established regression dependence with the selected standard (2.7-7.8%). This dependence is obtained at the speed of sound in austenite ~ 4000 m / s. It is determined that the application of the ultrasonic method allows to determine the content of residual austenite in the samples of roll steels quite quickly and accurately.
1 January 2018 in Fundamental and applied problems of ferrous metallurgy
The aim of the work is to study the phase-structural transformations during cooling of carbon and low-alloy steels, taking into account the resulting structural deformations and stresses. Low-alloyed steels with different content of alloying elements - chromium, molybdenum, nickel and steel, micro-alloyed with vanadium were chosen as the object of research. The dilatograms of steel samples were used to find the relative expansion of the steel sample before the start of austenite phase transformation (DA) and the relative expansion of the steel sample during austenite phase transformation (DFТ), which are associated with the relative elongation of the sample through a constant factor K. The parameter DA allows you to find structural stresses that arise in supercooled austenite steel in the presence of a temperature gradient. The parameter DFТ characterizes the stresses created by the phase transformation of austenite. As a result of the performed regression analysis, dependences were obtained that link the chemical composition of the steel, its cooling rate, and the parameters DА and DFТ. The analysis of phase-structural transformations during the cooling of the steel with the occurring deformations and stresses. An empirical relationship has been established between the temperatures of the beginning and end of the phase transformation of austenite in steel, the physicochemical parameters d and Zy, the cooling rate, and the deformation parameters when the austenite is cooled DA and the phase transformation DFТ. Confirmed the adequacy of the constructed equations. The obtained regression equations make it possible to calculate the deformation parameters DA and DFТ and critical points of the steel Ac1 and Ac3.
1 January 2020 in Fundamental and applied problems of ferrous metallurgy
The purpose of the work is to determine rational schemes for their production by analyzing the technological and design parameters of a number of broadband mills that roll hot-rolled strips less than 2,0 mm thick. It is shown that at present there is a constant increase in the production of extremely thin hot-rolled strips (0,8-1,5 mm thick), which can be used instead of more expensive (by $ 20-30 per ton) cold-rolled strips. The development of the production of hot-rolled strips of such a thickness is limited by a number of problems, in particular, the low temperature of the end of rolling (760-820 °C), which leads to a significant decrease in the ductility of the rolled stock; limiting the rolling filling speed, which does not allow increasing the temperature of the end of rolling the complexity of controlling the cross-sectional profile and flatness of the strips. Using mathematical modeling, it was found that the strip thickness and rolling speed have the greatest influence on the temperature of the end of rolling. The thickness and temperature of the rolls at the entrance to the finishing group of stands have a lesser effect. A decrease in the number of stands in the finishing group increases the temperature of the end of rolling at a constant thickness of the rolls, but when the thickness of the rolls changes in accordance with the number of stands, the effect is significantly reduced. The most favorable technological parameters for the production of extra-thin hot-rolled strips are provided by casting and rolling units, which are characterized, in comparison with broad-strip mills, as a rule, by a greater thickness and temperature of the rolls (or continuously cast slabs) and a smaller number of stands. An increase in the thickness of billets (slabs) requires an increase in the permissible values of the energy-power parameters of rolling, as well as the use of special solutions that will ensure minimal heat loss by the rolls before entering the finishing group of stands. Calculations show that, based on the reliable maximum refueling speed of hotrolled strips (10-11.5 m / s) achieved in the industry, the minimum thickness of strips with high plastic characteristics is: for broad-strip mills - 1.9-2.0 mm; for casting and rolling units, depending on their type - 1.3-1.6 mm.
1 January 2018 in Fundamental and applied problems of ferrous metallurgy
The aim of the work is to review the analytical models of austenite decay, taking into account the internal stresses obtained by various authors. It is shown that a common drawback of the known works is the neglect of the effect of the stress-strain state arising during the heat treatment of parts on the kinetics of structural transformations, while the available experimental data indicate a significant effect of stresses and strains on structural transformations. It has been established that the experimental data accumulated to date do not allow reliably describing the effect of the stress state on structural transitions during the heat treatment of steels for the hot deformation tool. A simple theoretical expression is proposed for calculating the amount of martensite formed as a function of the voltage in the γ phase. It is theoretically shown that taking into account the voltage acting in the γ phase leads to an increase in the temperature of the end of the formation of martensite. Experimental study of this effect is especially convenient to carry out in isothermal conditions under uniaxial tension. It is shown that in order to reliably predict the structural state of the hot deformation tool during heat treatment, it is necessary to conduct a comprehensive study related to the experimental study of the effect of stresses on all types of transformations and the creation of an adequate mathematical model of austenite decomposition based on the obtained experimental data.
1 September 2022 in Metal and Casting of Ukraine
Predicting the survivability of rolling rolls
1 December 2019 in Metal and Casting of Ukraine
U(Ukraine) Pjsc Zaporizhstal Iron And Steel Works (Zaporizhzhia
Ukraine) Pjsc Zaporizhstal Iron And Steel Works (Zaporizhzhia