28 October 2024 in Kosmìčna nauka ì tehnologìâ
YYYuzhnoye State Design Office named after M. K. Yangel
Yuzhnoye State Design Office named after M. K. Yangel
+2
An investigation was done for heat-resistant coatings from Ni-Cr and Fe-Ni-Cr alloys, produced by vacuum arc deposition with cathodes from nichrome alloy ХН78Т and steel 12Х18Н10Т. The microstructural analysis of the studied coatings applied by vacuum arc deposition with different amounts of reactive gas (nitrogen) in a deposition chamber showed the presence of two phases: a matrix and the distributed particles of liquid phase of various sizes and shapes. Vacuum arc deposition at a cathode arc current of 55 A for Ni-Cr and 82 A for Fe-Ni-Cr coatings, a cathode arc voltage of 28 to 32 V, an underlayer temperature of 490±30 оС, and no nitrogen in the chamber gives coatings with no apparent orientation of crystallites and a microhardness reaching 330 to 374 HV. The diffusion mobility of atoms decreases at a higher nitrogen pressure, which results in a coarse-crystal, porous-columnar structure of coatings with high porosity, a varying volume, and a rough surface. The influence of nitrogen pressure in a chamber on the strength of coatings was evaluated by their microhardness. A nitrogen pressure gain up to 0.13 Pa results in the increased microhardness of both coating systems, and the further growth in pressure has almost no effect on microhardness. It was discovered that a nitrogen pressure of 0.13 Pa gives the optimum combination of a coating’s strength and continuous structure with no pores and apparent columnar crystallites. Alloys from Ni-Cr with 80 % Ni are among the most heat-resistant industrial materials with a maximum operating temperature of up to 1200 оС. However, they are expensive, which makes Fe-Ni-Cr alloys more attractive, providing their heat resistance is sufficient for the operating temperature range. Therefore, it is reasonable to conduct further research on both Ni-Cr and Fe-Ni-Cr coatings to develop a deposition technology that can provide the required performance parameters. Controlling nitrogen pressure makes it possible to adjust the structure and properties of the coating during deposition.
1 July 2025 in Materials Science
1 December 2025 in Fundamental and applied problems of ferrous metallurgy
The production of piston ring blanks from gray cast iron by the method of individual casting is complicated by the fact that the required structure of graphite and metal matrix is formed directly during the crystallization process without the use of heat treatment. In this regard, there is a need for strict control of both the chemical composition of the starting cast iron and the parameters of the casting process. The influence of overheating temperature, holding time and melt pouring temperature on the hardness and structure of cast blanks of compression piston rings of different sizes at a given chemical composition of cast iron (in wt.%) was assessed: C=3.72; Si=2.82; Mn=0.79; P=0.4; S=0.045; Ni=0.23; Cr=0.26; Cu=0.48; Mo=0.53; Ti=0.05. It is shown that fluctuations in the temperature of overheating and pouring of the melt within 10–50 °C and its holding time within 1–11 min. do not cause systemic changes in the hardness and microstructure of castings of ring blanks made of gray cast iron. The hardness along the blank rings is not uniform and is 94–112 HRB, which meets the requirements of GOST 621-87 "Piston rings for internal combustion engines". It has been established that the structure of graphite and metal matrix of castings of ring blanks from gray cast iron, despite compliance with the technological process of their production, often does not meet the requirements of the specified standard. The maximum size of graphite inclusions is 120–250 μm, which exceeds the required size of 80 μm according to GOST 621. To achieve compliance with the requirements of GOST 621-87 regarding the structure of graphite and the metal matrix, as well as to prevent a decrease in hardness after heat treatment of cast ring blanks, it is necessary to reduce the maximum size of graphite inclusions to 80 microns and ensure the formation of dispersed pearlite with no more than 5% hypoeutectoid ferrite. To obtain the required graphite structure and metal matrix, it is important not only to maintain the stability of the casting process, but also to adjust the composition of the cast iron melt taking into account the content of gases (O, N, H). Their concentration is directly related to the origin of the charge materials, among which blast furnace iron and secondary metal from our own production are of primary importance.
31 December 2024 in Metaloznavstvo ta obrobka metalìv
The relationship between chemical microheterogeneity of gray cast iron castings, revealed by the method of color etching in sodium picrate, and the structure of flake graphite was studied. The results of microstructural studies indicate that the crystallization of gray cast iron is accompanied by the emergence of several levels of chemical and structural microheterogeneities of the crystallizing melt, affecting the formation of graphite. Microstructural features indicate that the cast iron melt, which is close in carbon content to the eutectic composition, acquires a dendritic and cellular structure before the formation of graphite. The intensity of chemical microheterogeneity and its topology are hereditarily related to the location, size and shape of graphite inclusions. Flake graphite formed inside and on the periphery of melt cells has different structure and thickness of plates. The enrichment of areas of cast iron melt with silicon leads to the formation of dendrites of primary austenite and primary graphite of the largest size in them. The microhardness of ferrite in the dendrites of former primary austenite is approximately 1.5 times greater than the microhardness of ferrite in areas adjacent to inclusions of primary graphite. A close inverse correlation (r = –0.93) was established between the microhardness of ferrite in areas with different liquation intensities and the thickness of graphite flakes located in these areas. The greatest spread of microhardness values and width of graphite flakes is observed in the most liquated areas enriched with silicon in the center of the cells, corresponding to the location of eutectic colonies. In the spaces between the cells, graphite is observed with the smallest thickness of the flakes, which are located at the smallest distance from each other. It is necessary to continue research into the hereditary influence of the structure and physical and chemical properties of high-carbon iron melts on the mechanism of graphite formation and the features of its structure in cast irons.
1 January 2018 in Fundamental and applied problems of ferrous metallurgy
The aim of the work is to study the phase-structural transformations during cooling of carbon and low-alloy steels, taking into account the resulting structural deformations and stresses. Low-alloyed steels with different content of alloying elements - chromium, molybdenum, nickel and steel, micro-alloyed with vanadium were chosen as the object of research. The dilatograms of steel samples were used to find the relative expansion of the steel sample before the start of austenite phase transformation (DA) and the relative expansion of the steel sample during austenite phase transformation (DFТ), which are associated with the relative elongation of the sample through a constant factor K. The parameter DA allows you to find structural stresses that arise in supercooled austenite steel in the presence of a temperature gradient. The parameter DFТ characterizes the stresses created by the phase transformation of austenite. As a result of the performed regression analysis, dependences were obtained that link the chemical composition of the steel, its cooling rate, and the parameters DА and DFТ. The analysis of phase-structural transformations during the cooling of the steel with the occurring deformations and stresses. An empirical relationship has been established between the temperatures of the beginning and end of the phase transformation of austenite in steel, the physicochemical parameters d and Zy, the cooling rate, and the deformation parameters when the austenite is cooled DA and the phase transformation DFТ. Confirmed the adequacy of the constructed equations. The obtained regression equations make it possible to calculate the deformation parameters DA and DFТ and critical points of the steel Ac1 and Ac3.
1 January 2024 in Fundamental and applied problems of ferrous metallurgy
IUIron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
Iron and Steel Institute of Z. I. Nekrasov National Academy of Sciences of Ukraine
The application of the theory of fractals in materials science during the analysis or modeling of various types of structures and their relationship with material properties is the most widespread, accessible and reliable direction. The purpose of the work was to determine the fractal dimension of graphite inclusions depending on their shape and distribution in the structure of gray cast iron. The search for the average fractal dimension of graphite inclusions was carried out in a computer program, the essence of which is to determine the closest convergence of fractal dimension values calculated using cell and point methods. An example of the application of the specified computer program and algorithm for determining the fractal dimensions of graphite inclusions and the metal matrix, as well as other structural elements of gray cast iron, is provided. The obtained calculated values have specific numerical values, therefore, in the future, they can be used to create analytical models for the predictive determination of the quality of gray cast iron depending on the type of final structure. It is shown that the problem of reliable and most accurate quantitative determination of graphite inclusions in the structure of gray cast iron can be solved using the method of fractal analysis. The considered method for determining the fractal dimension can be useful when studying the features of structure formation processes and evaluating the evolution of graphite inclusions at different stages of gray cast iron processing, starting from the smelting stage and ending with the final heat treatment. In addition, fractal analysis can be used to determine and evaluate the influence of morphological parameters of graphite inclusions on the formation of gray cast iron quality indicators, which cannot be achieved using traditional methods of quantitative analysis. Further research will be aimed at establishing statistically significant correlations of the fractal dimension with the properties of gray cast irons, in particular the behavior of the hardness change taking into account the formation of mixed or transitional type structures.