Jun Tanaka

Jun Tanaka

Auto-generated profile, based on publicly available information

Jun Tanaka

Center for EUV lithography, Laboratory of Advanced Science and Technology for Industry, University of Hyogo

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 August 2019 in Applied Physics Express
Verified
Journal Article
Closed access
PDF file
TTTakanori Takahashi
Takanori Takahashi
RMRyoko Miyanaga
Ryoko Miyanaga
MFMami Fjiii
Mami Fjiii
JTJun Tanaka
Jun Tanaka
KTKazushige Takechi
Kazushige Takechi
YUYukiharu Uraoka
Yukiharu Uraoka

24 June 2019 in Journal of Photopolymer Science and Technology
Verified
Journal Article
Open access
PDF file
TITakuma Ishiguro
Takuma Ishiguro
JTJun Tanaka
Jun Tanaka
THTetsuo Harada
Tetsuo Harada
TWTakeo Watanabe
Takeo Watanabe
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies

24 June 2019 in Journal of Photopolymer Science and Technology
Verified
Journal Article
Open access
PDF file
JTJun Tanaka
Jun Tanaka
TITakuma Ishiguro
Takuma Ishiguro
THTetsuo Harada
Tetsuo Harada
TWTakeo Watanabe
Takeo Watanabe
The resist development is a critical issue in EUV lithography for high volume manufacturing of semiconductor devices. Especially, the resist should have low line-width roughness (LWR) performance in fine patterning. To reduce the LWR, it is significant to control and reduce the stochastic behavior in the resist material. We employed the resonant soft X-ray scattering (RSoXS) method to evaluate the non-uniformity of the resist material components such as base polymer, functional group, and photo-acid generator and so on. In RSoXS method, the soft X-ray scattering intensity from the resist is recorded by a CCD camera, which the incident photon energy irradiated to the resist sample was varied around the carbon absorption K-edge of 284 eV. Around the carbon absorption edge, the absorption spectrum had resonant absorption peaks that depended on the chemical bonding structure of carbon. The scattering signal profile of a commercial chemical-amplified resist was different at each absorption peaks, which indicated non-uniformity of resist material. Thus, the non-uniformity of the resist material was measured by RSoXS method, which was important for development of low LWR resist.

2 July 2021 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
KTKazushige Takechi
Kazushige Takechi
FLFeipeng Lin
Feipeng Lin
SHShui He
Shui He
YYYong Yuan
Yong Yuan
JTJun Tanaka
Jun Tanaka
KSKenji Sera
Kenji Sera
In this brief, we discuss top-gate InGaZnO thin-film transistors (InGaZnO TFTs) fabricated with boron (B) implantation into the source-drain regions, focusing on channel shortening. B was implanted through the gate insulator into the InGaZnO layer. From scanning capacitance microscopy (SCM) analysis, we found that boron implantation in the S/D regions of InGaZnO TFTs induces channel shortening. We also found that such channel shortening is suppressed by optimizing acceleration voltage in the boron implantation process, leading to good operation in short-channel (1.5 μm) InGaZnO TFT.

24 June 2019 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
YKYuya Kuwahara
Yuya Kuwahara
KTKazushige Takechi
Kazushige Takechi
JTJun Tanaka
Jun Tanaka
HTHiroshi Tanabe
Hiroshi Tanabe
We investigated the hump effect, which is induced by positive gate-bias stress, of an amorphous In-Ga-Zn-O thin-film transistor with the self-aligned top-gate structure. By applying scanning capacitance microscopy to the transistor with the hump effect, we directly detected a partial increase of carrier density at the channel edges in the channel width direction. The width of the high-carrier-density regions was approximately 1 μm at each side edge, which is consistent with the estimation by electrical measurements. Such high-carrier regions at the channel edges can act as parasitic transistors with a more negative threshold voltage, generating the hump in the transfer characteristics. Our results support the idea that the hump effect is derived from the parasitic transistors at the channel edges directly and show that the scanning capacitance microscopy provides complementary information to the electrical measurements and is an effective tool to evaluate the hump effect.

1 May 1993 in Polymers for Advanced Technologies
Verified
Journal Article
Closed access
PDF file
HKH. Kikkawa
H. Kikkawa
FSF. Shoji
F. Shoji
JTJ. Tanaka
J. Tanaka
FKF. Kataoka
F. Kataoka
HSH. Satou
H. Satou