John Long Soon

John Long Soon

Auto-generated profile, based on publicly available information

John Long Soon

University of Sydney

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 February 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JSJohn Long Soon
John Long Soon
DLDylan Lu
Dylan Lu
JPJimmy Chih-Hsien Peng
Jimmy Chih-Hsien Peng
WXWeidong Xiao
Weidong Xiao
Malfunction of power semiconductor switches is the dominant cause of failure in power electronic converters. This paper proposes a novel dual-switch dc-dc topology for high-reliability applications. The proposed converter is fault-tolerant and supports operation under both step-down and step-up modes. The proposed topology can be reconfigured automatically under various switch-fault conditions in order to maintain normal operation. This is enabled by an affine-parametrization-based control design which minimizes the transient impact of the faults. The reliability performance of the proposed converter is evaluated theoretically using a Markov model, demonstrating its superiority over conventional topologies. Finally, a laboratory prototype is developed and tested to verify the proposed design and control performance under switch faults.

20 October 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LQLing Qin
Ling Qin
LZLei Zhou
Lei Zhou
WHWaqas Hassan
Waqas Hassan
JSJohn Long Soon
John Long Soon
MTMin Tian
Min Tian
JSJiapeng Shen
Jiapeng Shen
A family of transformer-less single-switch dual-inductor high voltage gain boost converters is proposed in this paper. The proposed configurations can realize high voltage gain with low voltage and current stresses. The voltage gain of the proposed converters is analogous to the switched inductor boost converter; therefore, the proposed boost converters are suitable for high gain applications. The proposed family of converters has low component counts and reduced voltage stress on devices compared to three typical transformer-less single-switch high voltage gain converters including switched inductor boost converter, quadratic boost converter and quasi-Z-source boost converter. Moreover, the current stress of the front-end diode and the rear-end inductor is also relatively low. Therefore, the conversion efficiency is enhanced while keeping the cost low. The operation principles and steady-state characteristics analysis of the proposed converters under the inductor current continuous conduction mode (CCM) and continuous bidirectional conduction mode (CBCM) are discussed in detail. A prototype of 300V, 250W/100kHz is developed to verify the performance of the proposed converter. The experimental results substantiate the effectiveness and advantages. The prototype achieves a peak efficiency of 97.5%.

26 February 2016 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JSJohn Long Soon
John Long Soon
DLDylan Lu
Dylan Lu
This letter presents a method for selecting an appropriate rating of fuse and MOSFET in a fault-tolerant dc/dc converter to protect the circuit in a short-circuit operating condition. The proposed method is based on the Joule-integral principle to calculate the amount of energy associated with the fuse. Different fuse melting characteristics are used to select the appropriate melting time by comparing them with the thermal characteristics of the circuit. The tests performed demonstrate consistent behavior with simulation results and they show that the fuse current rating must be lower than the current rating of the switch in order to provide a safe and reliable operation of the converter.

13 April 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
WHWaqas Hassan
Waqas Hassan
JSJohn Long Soon
John Long Soon
DLDylan Lu
Dylan Lu
WXWeidong Xiao
Weidong Xiao
A DC-DC converter is proposed to achieve a high voltage conversion ratio for bidirectional power flow applications. The non-isolated topology is optimally designed to integrate both the switched capacitor and coupled inductor techniques for high efficiency. The windings of the coupled inductor are stacked at the low voltage source, which transfers any leakage energy of the coupled inductor directly into the output port and simplifies the clamping circuit. The optimal design keeps the voltage stress on the main switches low for the entire duty cycle operation. Thus, the converter demonstrates the advantage of wide-voltage gain based on common ground and low and steady voltage stress in both buck and boost modes of its operation. Furthermore, the converter can realize zero voltage switching (ZVS) through the synchronous rectifiers without requiring extra hardware circuitry to enhance conversion efficiency. The operation principle, including the steady-state analysis, dynamic modeling, controller design, efficiency analysis, and optimization, are discussed in detail and verified by the experimental test. The prototype substantiates the theoretical analysis and soft-switching operation. The converter exhibits the capability for load and line regulation and demonstrates a peak efficiency of 96.38% in the boost mode and 95.61% in the buck mode of operation.

19 August 2021 in IEEE Transactions on Power Systems
Verified
Journal Article
Closed access
JPJimmy Chih-Hsien Peng
Jimmy Chih-Hsien Peng
GRGurupraanesh Raman
Gurupraanesh Raman
JSJohn Long Soon
John Long Soon
NHNikosHatziargyriou Hatziargyriou
NikosHatziargyriou Hatziargyriou
Electric grids are seeing increasing adoption of renewables interfaced with power electronics. As the share of renewable generation increases, the inverters are expected to operate in grid-forming mode to replace large conventional synchronous generation. Further, in geographical islands and isolated/rural areas, inverters interfacing renewable generators and storage are used to form the grids and share the loads. Given the expected presence of grid-forming inverters in future power systems, there is an urgent need to revise education curricula about the stability issues arising from these interconnected inverters. Existing training is overly reliant on numerical simulation or on expensive tools such as real-time simulators. In this paper, we present a laboratory hands-on project dealing with small-signal stability in droop-controlled inverters. It entails simulation and hands-on experimentation for which an inexpensive microgrid set up was developed in-house at the National University of Singapore. The design project can be integrated into power engineering courses offered to senior and postgraduate students.

10 August 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LQLing Qin
Ling Qin
TQTianhong Qian
Tianhong Qian
JSJohn Long Soon
John Long Soon
WHWaqas Hassan
Waqas Hassan
YLYuhan Liu
Yuhan Liu
JMJingFeng Mao
JingFeng Mao
This paper presents an interleaved high-gain boost converter for standalone photovoltaic based electric vehicle charging. The proposed converter is an improvement on the conventional switched-capacitor boost converter, which is achieved by splitting the step-up network and introducing an additional input inductor and switch. The proposed converter features continuous input and output currents while significantly reducing the filter capacitance requirement. As a result, the need for an electrolytic capacitor is eliminated, leading to improved overall system reliability. In continuous conduction mode (CCM), when the driving signals of the two switches have a phase difference of $180^{\circ }$ and their duty cycles satisfy the constraint relationship of $d_\mathrm{2}=1/(2-d_\mathrm{1})$ , the proposed converter automatically achieves current sharing between the two input inductors throughout the entire duty cycle range. This feature eliminates the need for inductor current detection, reduces current stress, and lowers costs. Furthermore, the proposed converter offers twice the voltage gain of a conventional boost converter, with the voltage stresses of all power components equal to or close to half of the output voltage. The working principle, steady-state characteristics, small signal models and control method of the proposed converter in CCM are thoroughly analyzed. The operation of the proposed converter is validated through a comprehensive 500 W/50 kHz prototype experiment, which demonstrates the correctness of the theoretical analysis. The practical full-load efficiency exceeds 97% under wide variations in the input voltage, with a maximum measured efficiency of 97.9%.