Dmytro Petrachenko

Dmytro Petrachenko

Auto-generated profile, based on publicly available information

Dmytro Petrachenko

Відокремлений структурний підрозділ Глухівський агротехнічний фаховий коледж Сумського національного аграрного університету

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 April 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VSViktor Sheichenko
Viktor Sheichenko
DPDmytro Petrachenko
Dmytro Petrachenko
SKSerhii Koropchenko
Serhii Koropchenko
IRIvan Rogovskii
Ivan Rogovskii
Oleksandr GorbenkoOleksandr Gorbenko
Oleksandr Gorbenko
DSDenys Sheichenko
Denys Sheichenko
The object of research is technological processes, seeds of industrial hemp, and working bodies of the dehuller. A centrifugal-type device for crushing hemp seeds with a closed sector-type working body has been designed. Owing to this, the task related to seed dehulling was solved with a high level of efficiency in separating the seed coat from the kernel. The rational parameters for the dehuller have been substantiated: the diameter of the impeller is 162 mm, the gap between the impeller and the seed repelling panel is 80 mm, the frequency of rotation of the impeller is 2000 min–1. It was established that with the specified parameters and moisture content of the seeds within the limits of conditional (12.0–13.0 %), it is advisable to carry out dehulling process without preliminary separation of the seeds into fractions by width. It was established that an increase in seed size leads to a corresponding increase in the weight share of seed kernels. About 58.2 % of the main mass of seeds is the average fraction with a width of 2.5 to 3.0 mm. It was found that reducing the diameter of the impeller (from 236 mm to 162 mm) at a seed moisture content of 8.8 % improved the efficiency of dehulling. At a rotation frequency of the impeller of 2000 min–1, the highest total number of intact and destroyed kernels (23.23–29.33 %) was achieved for the two studied moistures. With an increase in seed moisture content from 8.8 % to 12.0 %, the number of dehulled kernels in the hempseed cake increased. It was noted that for seeds with a moisture content of 8.8 %, an increase in the gap led to a decrease in the dehulling efficiency for each of the three investigated seed fractions. The total number of dehulled kernels under such conditions decreased by 2.4–6.8 % and amounted to 16.4–26.9 %. For seeds with a moisture content of 12.0 %, an increase in the gap, on the contrary, increased the dehulling efficiency for each of the three investigated seed fractions. The total number of dehulled kernels for seeds of marked moisture increased within the range of 1.4–3.6 % and amounted to 27.4–31.0 % Об’єктом дослідження є технологічні процеси, насіння промислових конопель, робочі органи обрушувача. Розроблено пристрій відцентрового типу для обрушування насіння конопель із робочим органом закритого секторального типу. Завдяки цьому вирішено проблему обрушування насіння із високим рівнем ефективності відділення насіннєвої оболонки від ядра. Обгрунтовано раціональні параметри обрушувача: діаметр робочого колеса 162 мм, зазор між робочим колесом та відбивною декою 80 мм, частота обертання робочого колеса 2000 хв.-1. Встановлено, що за зазначених параметрів та вологості насіння в межах кондиційної (12,0–13,0 %) процес обрушування доцільно проводити без попереднього розділення насіння на фракції за шириною. Встановлено, що збільшення розмірів насіння призводить до відповідного зростання частки ваги насіннєвих ядер. Близько 58,2 % в основній масі насіння складає середня фракція шириною від 2,5 до 3,0 мм. Встановлено, що зменшення діаметру робочого колеса (від 236 мм до 162 мм) за вологості насіння 8,8 % підвищувало ефективність обрушування. За частоти обертання робочого колеса 2000 хв.-1 досягнуто найбільшу сумарну кількість цілих та зруйнованих ядер (23,23–29,33 %) для двох досліджуваних вологостей. Зі збільшенням вологості насіння від 8,8 % до 12,0 % кількість обрушених ядер в рушанці збільшувалося. Відзначено, що для насіння вологістю 8,8 % збільшення зазору призводило до зменшення ефективності обрушування для кожної з трьох досліджуваних фракцій насіння. Сумарна кількість обрушених ядер за таких умов зменшувалася в межах 2,4–6,8 % та складала 16,4–26,9 %. Для насіння вологістю 12,0 % збільшення зазору, навпаки, підвищувало ефективність обрушування для кожної з трьох досліджуваних фракцій насіння. Сумарна кількість обрушених ядер для насіння відміченої вологості збільшувалася в межах 1,4–3,6 % та складала 27,4–31,0 %

21 August 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VSViktor Sheichenko
Viktor Sheichenko
DPDmytro Petrachenko
Dmytro Petrachenko
IRIvan Rogovskii
Ivan Rogovskii
IDIgor Dudnikov
Igor Dudnikov
VSVitaliy Shevchuk
Vitaliy Shevchuk
RSRuslan Shatrov
Ruslan Shatrov
The subject of this study is the technological processes of separation, the hull of industrial hemp seeds, an aspiration column, and whole kernels. The problem solved was determining the technical and technological solutions that could enable the intensification of production processes for separating industrial hemp seeds. The separation of hemp seed hull by linear dimensions on sieves with round and elongated holes has been investigated. It was found that the percentage of seed hulls retained by sieves with circular holes was 25.98 % for ø3.5 mm, 23.59 % for ø3.0 mm, and 40.28 % for ø2.0 mm, respectively. Sieves ø3.5 mm and ø2.0 mm made it possible to obtain seed hulls fractions with two components conditionally different in the «mass-size» ratio. Using sieves with elongated holes enabled obtaining fractions consisting of at least three components. Sieves with elongated working holes of 3.0×20 mm, due to their low ability (1.76 %) to retain hemp seed hull components, were ineffective. The clogging levels of kernels in seed hulls, separated by linear dimensions on combined sieves with round and elongated holes, were as follows: separation option No. 1 – 48.70 %, option No. 2 – 45.74 %, option No. 3 – 60.25 %, option No. 4 – 49.32 %, respectively. It was established that the use of an aspiration column made it possible to remove up to 32.1 % of clogging in the form of a light fraction. The application of the aspiration column reduced the content of seed coating in separation option No. 1 by 3.0–5.7 times, option No. 2 by 1.35–3.7 times, option No. 3 by 1.9–11.2 times, and option No. 4 by 1.5–4.8 times, respectively. The quantitative and component composition of seed hulls fractions obtained under conditions of using an aspiration column with set rational values of the air damper opening angle α=53° and the vertical tilt angle of the air channel β=6°, was as follows: Stage I – «heavy» fraction – 51.78 %, 27.56 % – waste, up to 20 % – «light» fraction of Stages II and III

5 December 2020 in Bast and Technical Crops
Verified
Journal Article
Open access
DPDmytro Petrachenko
Dmytro Petrachenko
One of the current areas of processing of industrial hemp seeds is to obtain crushed seeds, which have high nutritional value and are a source of biologically active substances for the human body. The Institute of Bast Crops has developed a centrifugal crusher for crushing industrial hemp seeds, which shows positive results. Since the process of crushing of hemp seeds is little studied, it is logical to study it. It is known that the process of seed crushing is influenced by the properties of the seed (size, degree of ripeness, humidity) and technological parameters of the crusher. Therefore, in the process of research, the variable factors were the fraction of seeds in width (less than 2,5 mm, from 2,5 to 3,0 mm, more than 3,0 mm), seed moisture (8.8 and 21.6%), frequency rotation of the impeller of the crushing mechanism (1500 min.-1, 2000 min.-1, 2500 min.-1). It is established that with the change of each investigated parameter the result of crushing significantly changes, namely the quantitative composition of fractions “core” (crushed seeds), “nedorush” (not completely crushed seeds), “waste” (husk and ground seeds). Among the three fractions, the fine fraction of seeds is less susceptible to crushing, which allows to obtain from 6,82 to 17,61 % of the crushed seeds. The crushing of the middle fraction of seeds allows to obtain from 7,37 to 22,01 % of the crushed seeds. A large fraction of seeds in the process of crushing allows to obtain 10,95 – 23,33 % of the crushed seeds. With increasing humidity, the number of scrushed seeds increases. When processing seeds of higher moisture for each of the three fractions, we obtain an yield of crushed seeds of 1,0 – 3,0 % more compared to the treatment of seeds with lower humidity. The speed of the impeller has an ambiguous effect on the number of crushed seeds. Increasing the speed increases the number of crushed seeds, but until a certain point, after which there is a decrease. The best results for all three seed fractions were obtained at a humidity of 21,6 % and an impeller speed of 2000 min-1.

1 December 2018 in Bast and Technical Crops
Verified
Journal Article
Open access
DPDmytro Petrachenko
Dmytro Petrachenko
SKSerhiy Koropchenko
Serhiy Koropchenko
The article presents the results of studying the effectiveness of different methods of destruction of the seed coat, the establishment of the most promising design of the mechanism for the hemp seeds shelling.

20 May 2024 in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
Verified
Journal Article
Open access
PDF file
ВШВіктор Шейченко
Віктор Шейченко
ДПДмитро Петраченко
Дмитро Петраченко
ВШВіталій Шевчук
Віталій Шевчук
ДШДенис Шейченко
Денис Шейченко
У роботі на підставі аналізу існуючих способів відділення зовнішніх оболонок від ядер насінин різних сільськогосподарських культур встановлено перспективні техніко-технологічні рішення, застосування яких уможливить обрушування насіння промислових конопель з високим рівнем ефективності. Відмічено, що ефективність обрушування досягається завдяки врахуванню фізико-технологічних властивостей насіння культури. До таких властивостей відносять геометричні розміри, структуру оболонки та ядра, їх міцність, абсолютну та об’ємну маси, фрикційні властивості, вологість, вміст олії тощо. Неврахування будь-якого з параметрів суттєво впливає на кінцевий результат процесу обрушування. Виявлено, що техніко-технологічні рішення, які б із необхідним рівнем універсальності та ефективності забезпечували обрушування насіння різних культур, на даний час віднайти складно. Натомість компромісні рішення щодо налаштувань існуючих механізмів з урахуванням якості кінцевого продукту не забезпечують необхідний рівень ефективності оброблення. Отриманий результат характеризується або низькою якість кінцевого продукту, або значними втратами сировини. Встановлено, що кожний конкретний вид сільськогосподарської культури потребує використання такого способу обрушування, яким враховано фізико-технологічні властивості оброблюваного насіння. За умов розроблення обладнання для обрушування насіння конопель доцільно врахувати конструкційні особливості, переваги та недоліки існуючих технічних рішень обрушувачів насіння. Найбільш перспективним для обрушування насіння промислових конопель є спосіб одноразового удару, який реалізовано у відцентрових механізмах. Орієнтований удар насінини об деку уможливить збереження м’яких конопляних ядер. Ключові слова: насіння конопель, обрушення, способи обрушення насіння, відцентрові механізми

1 December 2019 in Bast and Technical Crops
Verified
Journal Article
Open access
DPDmytro Petrachenko
Dmytro Petrachenko
SKSerhiy Koropchenko
Serhiy Koropchenko
One of the promising directions for the use of industrial hemp seeds is the production of shelled seeds. The core of hemp seeds released from the inedible shell, as a standalone product, contains no digestible components, so it is a more valuable food product than the hemp seeds covered in the shell. The lack of technological equipment for destroying industrial hemp seeds impedes the development of this processing sector and makes research relevant in this area relevant. The effectiveness of oilseed crop destruction depends on the morphological and physico-mechanical properties of the directly treated seed. Finding the best method of destroying the seeds of industrial hemp is impossible without comparing the results of the efficiency of work of different means of operation of technical means. In the process of finding an effective method of collapse by the staff of the Engineering Research Department of the Institute of bast crops NAAS, among other things, the possibility of the collapse of hemp seeds by the method of repeated and single impact was explored. The principal possibility of shelling hemp seeds with the use of a machine type, where the multiple impact method is implemented, has been established. It is determined that this mechanism has several disadvantages. Excessive airflow is formed in the working chamber, which impedes the shelling process and affects the complexity of the structure. As the impeller rotates, the mechanism begins to act as a shredder: there is a significant increase in the fraction of ground seeds, that is, the seeds turn into oil dust. The basic possibility of demolition of hemp seeds by the method of focused single blow (centrifugal machines) is established. It is determined that this mechanism has several advantages, which simplifies the overall construction and principle of operation and is more promising for the sowing of hemp seeds. As a result, the design of a centrifugal stand for the shelling of hemp seeds was developed, the use of which allows to obtain 15.4% of the finished shelled kernel.