Distributed acoustic sensing (DAS) technology is, increasingly, the seismic acquisition mode of choice for its high spatial sampling rate, low cost, and nonintrusive deployability. It is being widely evaluated as an enabler of seismic monitoring for CO2 sequestration in building subsurface time-lapse images and in characterizing near-surface environments. To advance this evaluation, field seismic surveys with optical fibers have been conducted at the Containment and Monitoring Institute’s Field Research Station (CaMI.FRS) in Newell County, Alberta, Canada. In comparison to the standard geophones, optical fibers deployed in surface trenches at CaMI.FRS have recorded high-quality surface waves, rich in low frequencies and exhibiting limited spatial aliasing. These benefits have motivated us to apply the full-waveform inversion (FWI) approach to image the S-wave velocity (VS) and attenuation (quality factor QS) models at shallow site using the surface waves recorded by optical fibers. Compared to the conventional surface-wave dispersion approach, FWI can intrinsically incorporate fundamental and high-order modes and produce VS model with high spatial resolution that resolves horizontal variations. The low-frequency components below 10 Hz measured in the DAS recordings are helpful to overcome the cycle-skipping problem of FWI. Following the adjoint-state method, QS sensitivity kernel can be calculated efficiently with memory strain variables. The QS model is iteratively estimated with a new misfit function measuring root-mean-square amplitude differences, which helps to reduce the trade-off artifacts. The synthetic data obtained from the inverted models are consistent with the observed data in amplitude and phase. The inversion results provide valuable information to characterize the near-surface environments at CaMI.FRS and are expected to support seismic imaging in deeper CO2 injection zones.
We present the results of a feasibility study for seismic monitoring using conventional surface seismic experiments at the CaMI Field Research Station, Alberta, Canada, where a small volume of gas-phase CO 2 is being injected into a sandstone reservoir at a depth of 300 m. We first apply a careful fluid substitution procedure to the results of reservoir gas saturation and pressure responses obtained from fluid flow simulations. We test different methods to compute the bulk modulus of the fluid for different fluid saturation models. Assuming a semi-patchy model and considering only the replacement of brine with a maximum saturation of 50% CO 2 , we estimate the reduction in P-wave velocity to be 20%. Adding an increase in pore pressure of 2.7 MPa increases the P-wave velocity reduction to 32%. After including a field-based signal-to-noise ratio of 5% to the synthetic seismic data, the time-lapse seismic anomaly should be detectable after one year of injection (266 tonnes of CO 2 ).
Seismic data are a significant facilitator for monitoring in carbon capture and sequestration projects, providing high-resolution images of fluid migration, using, for example, full-waveform inversion (FWI). Distributed acoustic sensing (DAS), a relatively novel technology for wavefield sampling, is well suited for this type of monitoring. Using noninvasive optical fibers, DAS allows for dense spatial sampling along the entire length of the wellbore, without disrupting operations. Permanently installed in the wellbore, typically behind casing, DAS offers highly repeatable and dense sampling of the transmitted wave modes crucial to seismic monitoring of injected carbon dioxide (CO2). However, the DAS data consist of measurements of strain along the tangent of the fiber and therefore do not transfer directly to conventional FWI algorithms. Incorporation of DAS data in their native strain (or strain-rate) form in standard FWI algorithms, requires changing the definition of the receiver sampling operator to use geometric information about the fiber to supply tangential strain measurements to the FWI residual. The theoretical developments are applied to invert field vertical seismic profile data acquired with DAS fiber and accelerometers at a CO2 sequestration site in Newell Country, Alberta. Our method incorporates DAS data and accelerometer data in one objective function and allows us to tune the relative importance we wish to place on each data set. This method also transfers to noncollocated sensors, for example, surface-deployed geophones and borehole fiber. The inverted models contain features expected from the geology of the field site, and data modeled in the inverted models compare favorably with the field data for these sensor types. The models are derived from data acquired prior to CO2 injection, representing baseline models for future time-lapse studies planned at the field research station.
8 December 2022 in Journal of Geophysical Research: Solid Earth