Martensitic stainless steel AISI 431 and low carbon steel AISI 1020 are materials used together in many different industries. However, important problems are encountered when welding (fusion welding) these materials to each other. For this reason, friction welding process (Solid-state welding) is used to join these dissimilar metals. There are very few studies on joining these materials with friction welding. Therefore, the optimization of the welding parameters used in joining these dissimilar steel pairs with friction welding is of great important. In addition, the effects of the factors dependent on friction welding parameters need to be well understood. In this study, AISI 431 and AISI 1020 steel bars were successfully joined by friction welding, and the effects of welding parameters on tensile strength and axial shortening were investigated, and welding parameters were optimized using Taguchi method to obtain quality weld joints. The experimental results of the study showed that the highest tensile strength (573.32 MPa) of the joints was 54.53%, higher than the lowest tensile strength (370.99 MPa), the highest axial shortening (23.18 mm) was 650.16%, higher than the lowest axial shortening (3.09 mm). The optimal parameters for average axial shortening and average tensile strength were determined as A3B1C3 and A3B3C2; and the highest percentage contribution values for axial shortening and tensile strength were found to be 51.55% (rotating speed) and 63.90% (rotating speed); and R2 values for the average axial shortening and average tensile strengths were found to be 97% and 99.3%, respectively.
In this study, the analysis of cutting forces on medium carbon AISI 1050—to which different spheroidization heat treatments were applied—was conducted by the mixed-level Taguchi orthogonal experiment design method. In the experiments, besides the parameters of feed rate, depth of cut and cutting speed having effect on cutting forces as a factor in orthogonal design, the spheroidization time and temperature parameters were also used. By the performed orthogonal experiment design method, the values of cutting forces were estimated using the five-factor, two- and three-leveled Taguchi L36 (22 × 33) mixed orthogonal experiment design method. The effectiveness of the machining parameters on the cutting force was revealed by performing analysis of variance test. Moreover, the effectiveness rates of the parameters were also determined in the study as per the signal noise rates. Consequently, it has been observed that the feed rate is more effective on the cutting forces compared to other parameters.
31 July 2024 in Arabian Journal for Science and Engineering
In this study, the effects of Gr and B4C filler materials on drilling performance, mechanical, and tribological behaviors of glass fiber-reinforced epoxy composites were experimentally investigated. Glass fiber-reinforced composite materials filled with B4C and Gr at different weight ratios (5%, 10%, and 15%) were manufactured using hand lay-up method. The produced composite materials underwent various tests, including mechanical tests (tensile and flexural tests), tribological tests (wear behavior), and drilling tests under different parameters. Additionally, SEM images of the worn and fractured surfaces were examined. The addition of both B4C and Gr fillers adversely affected the mechanical properties of glass fiber-reinforced composites. It was observed that tensile and flexural strengths decreased with increasing filler ratios. However, the addition of B4C and Gr fillers enhanced the wear resistance of glass fiber-reinforced composites. It was revealed that in drilling operations, as the feed rate increased, the thrust forces increased, while the cutting speed increased, the thrust forces decreased. It was determined that delamination values in glass fiber reinforced composites decreased as the feed rate increase, while delamination values increased as the cutting speed increased. Generally, the thrust forces, vibration, delamination, and moment values obtained during the drilling of B4C-filled glass fiber composites were found to be higher compared to Gr-filled glass fiber composites.
26 December 2019 in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
Tornalama işlemlerinde, istenmeyen yüksek değerlerdeki yüzey pürüzlülük ve titreşim değerlerini gidermek için iş parçaları tezgâha doğru bir şekilde bağlanması gerekmektedir. Bir iş parçası ayna ve punta arasına uygun bir basınç ile bağlanmadığında, eksenden kaçık salgılı bir şekilde dönmeye ve bozulmaya neden olmaktadır. Bu da iş parçasında istenmeyen yüksek değerlerde yüzey pürüzlülük değerlerine ve titreşimlere neden olur. Bu çalışmanın amacı, AISI 304 paslanmaz çeliğinin tornalanmasında en düşük yüzey pürüzlülüğü ve titreşim değerlerini elde etmek için Taguchi metodu kullanılarak en uygun ayna ve punta basıncını tespit etmektir. İşleme deneylerinde 5 farklı ayna ve punta basıncı ve kesme parametreleri olarak ise sabit kesme hızı, ilerleme ve kesme derinliği alınmıştır. Deney tasarımı için Taguchi L25 (5^2) ortogonal dizilimi kullanılmıştır. En küçük en iyidir yaklaşımına göre sinyal/gürültü oranı kullanarak yüzey pürüzlülüğü ve titreşim değerleri için en uygun ayna ve punta basıncı belirlenmiştir. S/N oranlarına göre optimum ve en düşük titreşim değerlerini veren ayna ve punta basıncı sırasıyla 18 bar ve 5 bar iken, optimum yüzey pürüzlülük değerlerini veren ayna ve punta basıncı değerleri ise sırasıyla 18 bar ve 11 bar olarak tespit edilmiştir. Fakat en düşük yüzey pürüzlülük değeri ise ayna basıncı 18 bar ve punta basıncı 5 barda elde edilmiştir. Taguchi deney tasarımındaki S/N oranı sonuçlarına göre yüzey pürüzlülüğü ve titreşim üzerinde ayna basıncının punta basıncından daha önemli olduğu tespit edilmiştir. Sonuç olarak Taguchi yönteminin faktör tasarımı, ayna ve punta basıncı parametrelerinin optimizasyonu için basit, sistematik ve verimli bir yöntem olduğu bulunmuştur.