Mehmet Şükrü Adin

Dr. Mehmet Şükrü Adin

Mechanical engineering, Batman University, Batman, Turkey (Türkiye)
orcid
• Stanford’s World's Top 2% Scientist • Editorial board memb...

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2022 in Materials Testing
Verified
Journal Article
Closed access
HAHamit Adin
Hamit Adin
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin
In this investigation, mechanical properties of composite materials produced from woven jute type were investigated. These composites were produced in the form of epoxy adhesive layers by using hand lay-up method in which aluminum, mica and ceramic particles were added into epoxy as a structural adhesive by 2, 4 and 6 wt%. Samples produced according to ASTM D procedures were subjected to tensile and three point bending loads to examine the effect of the particles. Experimental results were presented in tables and graphs. As a result, it was observed that the tensile and bending failure loads of the composite materials obtained by using the particle reinforced adhesive increased. Also, the biggest rise in tensile strength was achieved with 4 wt% aluminum and the biggest increase in bending strength was observed for 2 wt% aluminum particles.

4 June 2023 in Journal of Adhesion Science and Technology
Verified
Journal Article
Closed access
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin

27 November 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin
HAHamit Adin
Hamit Adin
In recent years, consumers have become increasingly interested in natural, biodegradable and eco-friendly composites. Eco-friendly composites manufactured using natural reinforcing filling materials stand out with properties such as cost effectiveness and easy accessibility. For these reasons, in this research, a composite workpiece was specially manufactured using eco-friendly jute fibers. Two cost-effective cutting tools were specially produced to ensure high-quality machining of this composite workpiece. One of these specially manufactured cutting tools was subjected to DC&T (deep cryogenic treatment and tempering) processes to improve its performance. At the end of the research, when the lowest and highest Fd (delamination factor) values obtained with DC&T-T1 and T1 cutting tools were compared, it was observed that 5.49% and 6.23% better results were obtained with the DC&T-T1 cutting tool, respectively. From the analysis of the S/N (signal-to-noise) ratios obtained using Fd values, it was found that the most appropriate machining parameters for the composite workpiece used in this investigation were the DC&T-T1 cutting tool, a 2000 rev/min spindle speed and a 100 mm/min feed rate. Through ANOVAs (analyses of variance), it was discovered that the most significant parameter having an impact on the Fd values was the spindle speed, with a rate of 53.01%. Considering the lowest and highest Ra (average surface roughness) values obtained using DC&T-T1 and T1 cutting tools, it was seen that 19.42% and 16.91% better results were obtained using the DC&T-T1 cutting tool, respectively. In the S/N ratio analysis results obtained using Ra values, it was revealed that the most appropriate machining parameters for the composite workpiece used in this investigation were the DC&T-T1 cutting tool, a 2000 rev/min spindle speed and a 100 mm/min feed rate. In the ANOVAs, it was revealed that the most significant parameter having an effect on the Ra values was the feed rate at 37.86%.

3 August 2023 in Mechanics of Advanced Materials and Structures
Verified
Journal Article
Closed access
HRHadj Boulenouar Rachid
Hadj Boulenouar Rachid
DNDjebbar Noureddine
Djebbar Noureddine
BBBoutabout Benali
Boutabout Benali
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin

1 February 2021 in Materials Testing
Verified
Journal Article
Closed access
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin
EKErol Kılıçkap
Erol Kılıçkap
The use of adhesive joints is increasing in aerospace, aviation, automotive, construction and marine industry due to their easily applicable properties, low-costs and light weights compared to traditional jointing methods such as bolts, rivets, welding and soldering. Due to the high fatigue strength, resistance to seawater corrosion and light weight, aluminum alloys, with their high satiety, fracture strength, light weight, high specific strength and good dimensional stability and other properties, glass fiber reinforced composite materials have widespread uses.

18 December 2023 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
AMAnup Kumar Maurya
Anup Kumar Maurya
WKWaris Nawaz Khan
Waris Nawaz Khan
APAmar Patnaik
Amar Patnaik
Mehmet Şükrü AdinMehmet Şükrü Adin
Mehmet Şükrü Adin
RCRahul Chhibber
Rahul Chhibber
CPChandan Pandey
Chandan Pandey