28 March 2023 in Periodica Polytechnica Civil Engineering
The article presents the results of research on application of sintering and crystallization initiators based on a composition of blast-furnace granulated slag and glass wastes in the ceramic masses for production of ceramic paving blocks by vibro-pressing. The leading role of sintering and crystallization initiators in assuring the strong and dense structure of ceramic pieces was updated. The main laws of changes in physical and mechanical properties of ceramic paving stone samples depending on the amount of sintering and crystallization initiators in the burning temperature range 950–1000 °C have been established. It was determined that the availability of finely dispersed glass powder (fraction less than 0.1 mm) as a component of crystallization sintering initiators contributes to early emergence of liquid phase in the ceramic mass, as softening temperature of glass powder begins already at 720–750 °C. According to the results of X-ray phase and electron microscopic analysis it was determined that crystallization of low-temperature form of ß-wollastonite (CaSiO3) is observed in the samples burnt at the temperature range of 950–1000 °C. It was proved that the availability of ß-wollastonite in the ceramic mass serves as a reinforcing component. It has been established that high strength values are achieved in those compositions where ß-wollastonite crystallization in the burning products is the highest. As a result of scientific and experimental work the feasibility of producing the ceramic paving stones by vibropressing containing sintering and crystallization initiators that meet the requirements of quality, aesthetics, environmental friendliness, resource- and energy-saving was proved.
15 December 2020 in Series of Geology and Technical Sciences
Heat storage materials on the basis of liquid paraffins and their narrow fractions with the set temperature of phase transition and the increased heat capacity for enclosing the structures of buildings are received. A method of formulating compositions heat-storage materials with melting temperatures below 250C and increased heat capacity from a mixture of narrow fractions of commodity paraffins is proposed. The technique of obtaining heat-storage materials on the basis of commodity paraffin by mixing components, in obtaining HSM with specified thermal characteristics, the research of component composition, physico-chemical and thermophysical properties, in the research of their operational properties. The technical conditions for the obtained heat- storage materials on the basis of commodity paraffins are developed and the possibility of their application in the enclosing structures of buildings is substantiated. The developed heat-storage material with the set operational properties provides energy saving due to increase of heat capacity and intensity of heat exchange of enclosing designs of buildings.
13 September 2024 in Technobius
This article considers the possibility of using technogenic waste from the mechanical processing of Sastobe carbonate rocks as coarse and fine aggregates in the production of heavy concrete. X-ray diffractometric analysis CaCO3 d = (3.849-3.14-2.49-2.277-2.088-1.912-1.869 A0) and the endothermic peak in the temperature interval of 800-850°C in the differential-thermal analysis curve technogenic residues formed during mechanical processing of Sastobe carbonate rocks showed that it mainly consists of calcium carbonate. Studies have shown that fine and coarse aggregates based on carbonate rocks have a rough surface, which increases their specific surface area and ensures a strong bond with the cement stone. At the same time, technogenic waste contains 2-3% powder fraction up to 0.16 mm, this fraction serves as an active mineral mixture. As a result of research, the use of these wastes as fillers can reduce the consumption of traditional crushed stone and sand by 50% without reducing the physical and mechanical properties of concrete, replacing 50% of traditional fillers with technogenic fillers based on carbonate rocks, increasing the density of concrete (2490kg/m3), reducing its water absorption (0.66 %), strength (49.8 MPa) and frost resistance (F400) indicators made it possible to obtain concrete that is the same as the control sample and to reduce its cost without reducing the physical and mechanical properties of concrete and to improve the environmental conditions of the region.
15 January 2022 in Bulletin of Kazakh Leading Academy of Architecture and Construction
This article studies the properties of clay materials of the Turkestan region for the production of ceramic paving stones. The analysis of the obtained physico-mechanical and chemical-mineralogical results and dilatometric studies made it possible to develop compositions of ceramic masses that are most acceptable for obtaining samples of paving stones with improved properties. On the basis of raw materials compositions in the loam-bentonite system of the Ordabasinsky deposit, samples molded by vibropressing were obtained, the physical and mechanical parameters of which have positive dynamics and prove the possibility of obtaining high-quality ceramic paving stones.
28 February 2020 in Eastern-European Journal of Enterprise Technologies
Development of the engineering procedure for the thermotechnical calculation of a building envelope with air chambers and a heatreflecting coating
30 September 2024 in Mechanics and Technologies
This article presents research materials aimed at developing technology for the utilization lead slags of Yuzhpolymetal JSC in order to use them as a fine aggregate and mineral additives for concretes with specified performance properties. The results of physico-chemical studies have established the presence of calcite, quartzite, dolomite, ferruginous compounds in lead waste for use as aggregates and mineral additives for concrete. It was determined that when partially replacing 50% of natural raw materials with aggregates based on lead waste, the grade strength of concrete increases by 13.3% than that of the control composition, it was found that it is compositions with 50% replacement of natural filler with lead waste that show the highest strength characteristics. With the complete replacement of aggregates with these wastes, the compressive strength of concrete decreases. Heavy concretes with a compressive strength of up to 58.6 MPa were obtained, but due to the fact that the studied lead production waste contains up to 33% ferrous compounds, up to 5% copper, zinc and barium oxides, it is advisable to use lead slags as fillers after extracting metals from it.