The efficiency of carbon utilization and storage within the Pennsylvanian Morrow B sandstone, Farnsworth Unit, Texas, is dependent on three-phase oil, brine, and CO2 flow behavior, as well as spatial distributions of reservoir properties and wettability. We show that end member two-phase flow properties, with binary pairs of oil–brine and oil–CO2, are directly dependent on heterogeneity derived from diagenetic processes, and evolve progressively with exposure to CO2 and changing wettability. Morrow B sandstone lithofacies exhibit a range of diagenetic processes, which produce variations in pore types and structures, quantified at the core plug scale using X-ray micro computed tomography imaging and optical petrography. Permeability and porosity relationships in the reservoir permit the classification of sedimentologic and diagenetic heterogeneity into five distinct hydraulic flow units, with characteristic pore types including: macroporosity with little to no clay filling intergranular pores; microporous authigenic clay-dominated regions in which intergranular porosity is filled with clay; and carbonate–cement dominated regions with little intergranular porosity. Steady-state oil–brine and oil–CO2 co-injection experiments using reservoir-extracted oil and brine show that differences in relative permeability persist between flow unit core plugs with near-constant porosity, attributable to contrasts in and the spatial arrangement of diagenetic pore types. Core plugs “aged” by exposure to reservoir oil over time exhibit wettability closer to suspected in situ reservoir conditions, compared to “cleaned” core plugs. Together with contact angle measurements, these results suggest that reservoir wettability is transient and modified quickly by oil recovery and carbon storage operations. Reservoir simulation results for enhanced oil recovery, using a five-spot pattern and water-alternating-with-gas injection history at Farnsworth, compare models for cumulative oil and water production using both a single relative permeability determined from history matching, and flow unit-dependent relative permeability determined from experiments herein. Both match cumulative oil production of the field to a satisfactory degree but underestimate historical cumulative water production. Differences in modeled versus observed water production are interpreted in terms of evolving wettability, which we argue is due to the increasing presence of fast paths (flow pathways with connected higher permeability) as the reservoir becomes increasingly water-wet. The control of such fast-paths is thus critical for efficient carbon storage and sweep efficiency for CO2-enhanced oil recovery in heterogeneous reservoirs.
Rock fractures are a key contributor to a broad array of Earth surface processes due to their direct control on rock strength as well as rock porosity and permeability. However, to date, there has been no standardization for the quantification of rock fractures in surface process research. In this work, the case is made for standardization within fracture-focused research, and prior work is reviewed to identify various key datasets and methodologies. Then, a suite of standardized methods is presented as a starting “baseline” for fracture-based research in surface process studies. These methods have been shown in pre-existing work from structural geology, geotechnical engineering, and surface process disciplines to comprise best practices for the characterization of fractures in clasts and outcrops. This practical, accessible, and detailed guide can be readily employed across all fracture-focused weathering and geomorphology applications. The wide adoption of a baseline of data collected using the same methods will enable comparison and compilation of datasets among studies globally and will ultimately lead to a better understanding of the links and feedbacks between rock fracture and landscape evolution.
The mechanism of face-centered-cubic (FCC)-Al formation at an L12-Al3Sc/liquid-Al interface was investigated on the basis of interfacial structure and misfit strains, by using ab initio molecular dynamics (AIMD). These simulations were performed using Born–Oppenheimer dynamics, where pressure and temperature was controlled using a Parrinello–Rahman barostat and Langevin thermostat, respectively. Through this approach, we compared the relative stability of (001) /liquid-Al and (111) /liquid-Al interfaces and examined their effect on the heterogeneous nucleation of FCC-Al. Enhanced interfacial bonding along stabilized the (001) /liquid-Al, and formed in-liquid ordered layer resembling (002) . Subsequently, the (001) /liquid-Al interface was subjected to stepwise cooling from 1450 to 950 K. The (002)-ordered layer was found to promote layer-by-layer epitaxial growth of FCC-coordinated regions to fraction. During cooling, the resulting misfit strains—at (001) /(002)-ordered layer and (001) /(002) interfaces—ranged from to 0.5% within 1450–950 K. The magnitude of such misfit strains reduced significantly between 1250 and 950 K, and this trend coincided with a sharp increase in FCC coordination. Thus, AIMD simulations revealed heteroepitaxial formation of FCC-Al on the (001) faces of intermetallic Al3Sc, and that this mechanism is closely associated with a reduction in misfit strains. Our findings motivate the search for new elements that will stabilize potent L12-like structures and produce grain-refinement in Al-based alloys.
11 February 2024 in Science of The Total Environment
Carbon capture, utilization, and storage (CCUS) has been widely applied to enhance oil recovery (CO2-EOR). A thorough investigation of the impact of injecting CO2 into a heterogeneous reservoir is critical to understanding the overall reservoir robustness and storage performance. We conducted fifteen flow-through tests on Morrow B sandstone that allowed for chemical reactions between a CO2-rich brackish solution and the sandstones, and four creep/flow-through tests that simultaneously allowed for chemical reactions and stress monitoring. From fluid chemistry and X-ray computed tomography, we found that the dissolution of disseminated cements and the precipitation of iron-rich clays did not significantly affect the permeability and geomechanical properties. Minor changes in mechanical properties from Brazilian and creep tests indicated that the matrix structure was well-supported by early diagenetic quartz overgrowth cement and the reservoir’s compaction history at deep burial depths. However, one sample experienced a dissolution of poikilotopic calcite, leading to a permeability increase and significant tensile strength degradation due to pore opening, which overcame the effect of the early diagenetic cements. We concluded that the Morrow B sandstone reservoir is robust for CO2 injection. Most importantly, cement timing, the abundance and texture of reactive minerals, and the reservoir’s burial history are critical in predicting reservoir robustness and storage capacity for CO2 injection.