9 October 2019 in Journal of Fluid Mechanics
A thorough self-similarity analysis is presented to investigate the properties of self-similarity for the outer layer of compressible turbulent boundary layers. The results are validated using the compressible and quasi-incompressible direct numerical simulation (DNS) data shown and discussed in the first part of this study; see Wenzelet al. (J. Fluid Mech., vol. 880, 2019, pp. 239–283). The analysis is carried out for a general set of characteristic scales, and conditions are derived which have to be fulfilled by these sets in case of self-similarity. To evaluate the main findings derived, four sets of characteristic scales are proposed and tested. These represent compressible extensions of the incompressible edge scaling, friction scaling, Zagarola–Smits scaling and a newly defined Rotta–Clauser scaling. Their scaling success is assessed by checking the collapse of flow-field profiles extracted at various streamwise positions, being normalized by the respective scales. For a good set of scales, most conditions derived in the analysis are fulfilled. As suggested by the data investigated, approximate self-similarity can be achieved for the mean-flow distributions of the velocity, mass flux and total enthalpy and the turbulent terms. Self-similarity thus can be stated to be achievable to a very high degree in the compressible regime. Revealed by the analysis and confirmed by the DNS data, this state is predicted by the compressible pressure-gradient boundary-layer growth parameter $\unicode[STIX]{x1D6EC}_{c}$ , which is similar to the incompressible one found by related incompressible studies. Using appropriate adaption, $\unicode[STIX]{x1D6EC}_{c}$ values become comparable for compressible and incompressible pressure-gradient cases with similar wall-normal shear-stress distributions. The Rotta–Clauser parameter in its traditional form $\unicode[STIX]{x1D6FD}_{K}=(\unicode[STIX]{x1D6FF}_{K}^{\ast }/\bar{\unicode[STIX]{x1D70F}}_{w})(\text{d}p_{e}/\text{d}x)$ with the kinematic (incompressible) displacement thickness $\unicode[STIX]{x1D6FF}_{K}^{\ast }$ is shown to be a valid parameter of the form $\unicode[STIX]{x1D6EC}_{c}$ and hence still is a good indicator for equilibrium flow in the compressible regime at the finite Reynolds numbers considered. Furthermore, the analysis reveals that the often neglected derivative of the length scale, $\text{d}L_{0}/\text{d}x$ , can be incorporated, which was found to have an important influence on the scaling success of common ‘low-Reynolds-number’ DNS data; this holds for both incompressible and compressible flow. Especially for the scaling of the $\bar{\unicode[STIX]{x1D70C}}\widetilde{u^{\prime \prime }v^{\prime \prime }}$ stress and thus also the wall shear stress $\bar{\unicode[STIX]{x1D70F}}_{w}$ , the inclusion of $\text{d}L_{0}/\text{d}x$ leads to palpable improvements.
1 April 2017 in AIAA Journal
Two-dimensional, direct numerical simulations are used to study the impact of active and natural (passive) suction at forward-facing steps on laminar–turbulent transition. Suction is applied through a gap in front of a step that is located in a flat-plate boundary-layer flow without streamwise pressure gradient. A steady base flow is used with a Mach number of 0.6. Subsequently, Tollmien–Schlichting waves are introduced by suction and blowing at the wall, and their growth over the surface imperfection is evaluated by factors. The investigated step heights are in the range of one to two times the local displacement thickness of the smooth flat plate. Both sharp and rounded step corners are investigated. Cases with and without suction are compared with the smooth flat plate without suction based on factors according to the method. Thus, it is shown that suction is capable to compensate or even overcompensate the negative impact of different steps on laminar–turbulent transition. The work concludes with a configuration that allows natural (passive) suction in front of a forward-facing step. Here, a significant reduction of the factor compared to the smooth flat plate without suction is possible. Further estimations indicate that a net drag reduction may be possible as well.
2 December 2020 in Journal of Fluid Mechanics
This paper presents a quantitative evaluation of the Reynolds analogy factor turns out to be well approximated by the analytical relation derived by So (Intl J. Heat Mass Transfer, vol. 37, 1994, pp. 27–41) for incompressible flow if a fixed, calibrated Reynolds number is used. Moreover, the effects of non-self-similarity prior to the self-similar region are assessed.
20 July 2022 in Journal of Fluid Mechanics
The transition to turbulence induced by counter-rotating wall-normal rotating cylindrical roughness pairs immersed within a laminar boundary layer on a flat plate is investigated with direct numerical simulations, dynamic mode decomposition (DMD) and perturbation kinetic energy (PKE) analysis. As long as the cylinder stub is rotating, the wake contains a steady dominating inner vortex (DIV) surrounded by a secondary inner vortex. Its circumferential velocity accelerates the fluid on one side of the cylinder and decelerates it on the other side. With low rotation speed, the perturbation is initiated by a combination of elliptical and centrifugal instabilities in the near wake. At medium rotation speeds, Taylor–Couette-like streamwise vortices are generated on the decelerated side, resulting in a protruding reverse-flow zone. Results from DMD analysis and corresponding PKE analysis reveal the unstable nature of the deceleration region and the wake. At the largest rotation speed investigated, the onset of perturbations is directly located on the decelerated side of the cylinder stubs, where a deceleration mechanism feeds the instability. In the near wake, the mechanism gradually changes to a pure centrifugal instability when the rotation speed increases. In the far wake, both elliptical and centrifugal instabilities fade away, and the streaky flow featuring a vigorous DIV is then only subject to inviscid inflectional instability.
13 July 2022 in Physical Review Fluids
This study extends the input-output framework for the receptivity analysis of an incompressible boundary layer introduced by Ran et al. [ Phys. Rev. Fluids 4, 093901 (2019)] to the laminar adiabatic supersonic case. Spatially distributed in the wall-normal direction, a -correlated Gaussian noise is considered as input, both including the velocity and temperature fields. Similarly, components of the resulting velocity and/or temperature fields are chosen as outputs. To study effects on the boundary layer, the measurements of the output are restricted within the boundary layer thickness, implying, however, that effects like acoustic radiation to the free stream are outside the scope of the present analysis. The main goal of the study is twofold: first, to demonstrate the potential of the chosen approach by comparison with familiar results, and second, to extend the current state of knowledge in the compressible regime in selected points by exploiting the extended capabilities of the chosen framework. To this end, the importance of the different inputs—especially the temperature effects—for the amplification of two-dimensional, oblique flow structures and streaks are discussed. Furthermore, the influence of first and second Mach modes (not present in the incompressible regime) is identified within the stochastic framework and results are discussed in light of previous receptivity analyses where the output is restricted to a single mode. By varying the spatial distribution of the forcing, the dependence of the receptivity on the wall-normal position, where the forcing is introduced, is illustrated and discussed. Finally, dominant coherent structures are identified by evaluating the first singular vector of the correlation matrix (proper orthogonal decomposition (POD) modes). By analyzing the dependence of both forcing and response POD modes on the choice of the measured component, further insight is provided about the contribution of temperature fluctuation to the stochastically maintained variance of the system.
1 February 2012 in AIAA Journal
An extended e^N-based modeling approach for Tollmien–Schlichting-type transition in aerodynamic flow simulations with the low-Re epsilon^h-Reynolds-stress model is presented. Instead of simply activating the turbulence production terms at the transition location (point-transition approach), the method incorporates the otherwise neglected Reynolds-stress contributions by the fluctuations of the Tollmien–Schlichting waves and provides them as local input for the turbulence model at the transition point. The shapes of the Reynolds-stress profiles are derived from linear stability analysis within the e^N method, whereas their absolute magnitudes are calibrated with the aid of direct numerical simulation data of a transitional boundary layer with adverse-pressure gradient. The dissipationrate input is adjusted to theoretically match the amplification rate of the fluctuations but requires a correction to account for the low-Re damping in the epsilon^h-Reynolds-stress model. The paper describes the general modeling ideas and the implementation in the flow solver. Aspects of the numerical discretization and a verification for threedimensional flows are addressed as well. Besides a basic validation for the adverse-pressure-gradient boundary layer, simulations of the SD7003 airfoil flow comprising a laminar separation bubble are presented, which yield very good agreement with measurements. Results of a transitional flat-plate flow are, however, impaired by the lack of intermittency modeling. Finally, the method is applied to a flowthrough nacelle near stall conditions in order to prove\ud its ability to compute consistent transitional behavior in complex three-dimensional flows