Tristan M. Römer

Tristan M. Römer

Auto-generated profile, based on publicly available information

Tristan M. Römer

University of Stuttgart

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2022 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
YWYongxiang Wu
Yongxiang Wu
TRTristan Römer
Tristan Römer
GAGabriel Axtmann
Gabriel Axtmann
URUlrich Rist
Ulrich Rist
The transition to turbulence induced by counter-rotating wall-normal rotating cylindrical roughness pairs immersed within a laminar boundary layer on a flat plate is investigated with direct numerical simulations, dynamic mode decomposition (DMD) and perturbation kinetic energy (PKE) analysis. As long as the cylinder stub is rotating, the wake contains a steady dominating inner vortex (DIV) surrounded by a secondary inner vortex. Its circumferential velocity accelerates the fluid on one side of the cylinder and decelerates it on the other side. With low rotation speed, the perturbation is initiated by a combination of elliptical and centrifugal instabilities in the near wake. At medium rotation speeds, Taylor–Couette-like streamwise vortices are generated on the decelerated side, resulting in a protruding reverse-flow zone. Results from DMD analysis and corresponding PKE analysis reveal the unstable nature of the deceleration region and the wake. At the largest rotation speed investigated, the onset of perturbations is directly located on the decelerated side of the cylinder stubs, where a deceleration mechanism feeds the instability. In the near wake, the mechanism gradually changes to a pure centrifugal instability when the rotation speed increases. In the far wake, both elliptical and centrifugal instabilities fade away, and the streaky flow featuring a vigorous DIV is then only subject to inviscid inflectional instability.

13 February 2023 in Experiments in Fluids
Verified
Journal Article
Open access
PDF file
TRTristan M. Römer
Tristan M. Römer
KSKai A. Schulz
Kai A. Schulz
YWYongxiang Wu
Yongxiang Wu
CWChristoph Wenzel
Christoph Wenzel
URUlrich Rist
Ulrich Rist
Delaying laminar–turbulent transition in boundary layers is of great interest since the skin-friction coefficient can be reduced by up to one order of magnitude. In this experimental research, it is shown that counter-rotating cylindrical roughness elements are able to delay transition under realistic flow conditions. Evidence is given by the intermittency, evaluated from hot-film measurements in a laminar water channel. An increase in rotation speed results in a delay of transition of up to $${6.5}{\%}$$ 6.5 % in the center of the plate. This trend can be explained by the streaks amplified by the rotating cylinders, resulting in a damping of the fluctuation amplitude in the boundary layer. The advantage of this method is that the transition delay can be actively controlled with conventional cylindrical roughness elements. Graphical

3 December 2024 in Experiments in Fluids
Verified
Journal Article
Open access
PDF file
TRTristan M. Römer
Tristan M. Römer
MKMarkus J. Kloker
Markus J. Kloker
URUlrich Rist
Ulrich Rist
CWChristoph Wenzel
Christoph Wenzel
In this study, the influence of various turbulence-grid configurations is analysed on both the induced free-stream turbulence (FST) and the resulting Klebanoff modes/streaks developing in a laminar flat-plate boundary layer downstream in a laminar water channel. All results are based on hot-film and particle image velocimetry measurements as well as visualizations. The grid design and installation has been done according to common grid installation recommendations to ensure homogeneous FST causing meandering Klebanoff modes inside the boundary layer. But it was found that (i) the Klebanoff modes do not meander for all grid configurations, (ii) not all configurations cause Klebanoff modes with the expected temporal and spatial behaviour, and (iii) for some configurations, the spanwise streak spacing is strictly locked to the grid spacing (mesh width). As these observations are unreported in the literature, this study is aimed at a thorough description of the influence of key grid parameters on the FST and the resulting streaks within the boundary layer. The investigation includes the grid parameters typically reported, such as the grid-bar diameters, the associated Reynolds numbers, or the streamwise placement of the grid, but now also the grid-orientation order (horizontal/vertical or vertical/horizontal order of grid bars of the dual-plane grid), the wall-normal position of the horizontal bars relative to the leading edge of the flat plate, and the existence of palpable imperfections in the manufactured grids. The Reynolds-number range covered lies well in the lower band of wind-tunnel experiments. Thus, this study suggests that the reliability and reproducibility of future experimental studies on FST would be greatly improved if they demonstrated homogeneity in the free-stream in both spanwise and wall-normal directions, documented the ongoing meandering and wavelengths of the generated Klebanoff modes and thus (implicitly) documented the spanwise independence of the results in the temporal mean. The latter is a prerequisite for the reliable investigation of FST/isolated-roughness interactions. Graphical abstract

23 September 2023
Verified
Book Chapter
Closed access
PDF file
TRTristan M. Römer
Tristan M. Römer
CWChristoph Wenzel
Christoph Wenzel
URUlrich Rist
Ulrich Rist

29 May 2026 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
TRTristan M. Römer
Tristan M. Römer
MKMarkus J. Kloker
Markus J. Kloker
URUlrich Rist
Ulrich Rist
CWChristoph Wenzel
Christoph Wenzel
This study experimentally examines how free stream turbulence (FST) alters roughness-induced transition by exposing cylindrical roughness elements of diameter-to-height ratios $\eta =1,2,3$ to three FST levels ( $ \textit{Tu}\approx 0.05\,\%$ , $1.15\,\%$ , $1.55\,\%$ ). Although the roughness Reynolds number $ \textit{Re}_{\textit{kk}}$ is varied solely through the free stream velocity, a detailed characterisation of the incoming FST and resulting Klebanoff modes shows that their variation remains moderate, enabling a controlled assessment of FST effects. The FST consistently promotes earlier transition for all $\eta$ at subcritical global-instability Reynolds numbers, but its influence on the underlying instability mechanisms depends strongly on $\eta$ . For the ‘thick’ cylinders ( $\eta =2,3$ ), the global instability remains remarkably robust: the dominant varicose mode and its frequency scaling show virtually no sensitivity to FST. In contrast, the ‘thin’ cylinder ( $\eta =1$ ) exhibits an extreme susceptibility: already moderate FST suppresses the sinuous mode predicted by global stability theory at supercritical Reynolds numbers. These findings provide a clear, experimentally grounded explanation for why global stability predictions often fail to materialise the structures in real, turbulence-contaminated environments and establish FST as a decisive factor governing whether, when and how roughness-induced instabilities manifest.