Dmytro Olegovitch Bannikov

Dmytro Olegovitch Bannikov

Auto-generated profile, based on publicly available information

Dmytro Olegovitch Bannikov

Ukrainian State University of Science and Technologies

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 May 2019 in Science and Transport Progress
Verified
Journal Article
Open access
PDF file
NKN. G. Kruhlikova
N. G. Kruhlikova
DBD. О. Bannikov
D. О. Bannikov
Purpose. Recently, the demand for reuse of industrial buildings that have not been in operation for some time has been increasing in Ukraine. Herewith, quite often the design of their roof requires the complete replacement and renovation by using modern roofing materials to meet the requirements of new government standards. Therefore, the choice and justification of the rational design of steel roof on the example of a short-span industrial building (18-24 m span), which is planned to be returned to exploitation after idle time, is the main goal of this publication. The object of the analysis is an unheated building equipped with bridge cranes of a small capacity (up to 10 tons). Me-thodology. To achieve this purpose, the comparison of structural variants of a roof steel collar tie was performed. Such variants include two types of collar tie cross-section –a lattice truss and a solid I-girder. The first type was analyzed for four possible types of section of elements – double angles, a roll-welded square profile, an electric-welded round tube and a rolled round tube. The second type was analyzed for two possible types of section – rolled I-section made of normal strength steel and fabricated sections of thin-gage high-strength steel. The design variants were compared on the basis of a numerical analysis of their work using the finite element method based on the software complex SCAD for Windows. Findings. According to the research results it should be stated that for the conditions of the city of Dnipro the most cost-effective variant of the steel collar tie cross section for the short-span industrial building is the truss made of electric-welded round tubes. Also the construction of collar tie made of roll-welded square profiles or fabricated section of thin-gage high-strength steel is considered quite effective. Originality. The research presented in the publication allows estimating the possibility and economic efficiency of usage for various types of cross-sections for the collar tie of a steel non-insulated roof of the industrial building for the reconstruction conditions in the Dnipro-city. Practical value. A practical estimation of mass and cost parameters for steel collar ties of various types has been carried out, and the methodology for conducting such estimation has been substantiated.

23 August 2019 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
DBDmytro Olegovitch Bannikov
Dmytro Olegovitch Bannikov
ARAnatoliy Valentinovitch Radkevich
Anatoliy Valentinovitch Radkevich
NNNataliya Anatoliivna Nikiforova
Nataliya Anatoliivna Nikiforova
This article is devoted to the analysis of one of the most common structural designs of the steel frame of small spans, currently used in India in construction and reconstruction for seismic areas. This scheme constructively involves the implementation of the main bearing elements - bolts and columns - in the form of a spatial truss box section. At the same time, rather simple rolling profiles from small-sized corners are used, as well as a round steel bar. The studies performed by the authors were carried out using the finite element method based on the national design computing complex SCAD for Windows. The loads, as well as the geometrical characteristics of the profiles, were taken according to the current building standards of India. Based on the results of the analysis, a number of recommendations were formulated to improve the efficiency of the considered design scheme for seismic effects of varying intensity.

26 December 2019 in Bridges and tunnels: Theory, Research, Practice
Verified
Journal Article
Open access
PDF file
VBV. M. Bezsalyi
V. M. Bezsalyi
DBD. O. Bannikov
D. O. Bannikov
Мета. Виконати інженерну оцінку ефективності застосування сталевих тонкостінних оцинкованих профілів на прикладі інженерної конструкції у вигляді арки. Сформулювати рекомендації щодо доцільності використання таких профілів порівняно з іншими більш традиційними видами сортаментних профілів. Методика. Для досягнення поставленої мети проведено серію чисельних розрахунків аркової конструкції, виконаної із трьох типів сталевих сортаментних профілів – безшовних гарячедеформованих труб, електрозварних прямошовних труб і тонкостінних оцинкованих профілів. При цьому варіювались прольоти аркової конструкції в діапазоні від 12 до 24 м і крок її розташування в діапазоні від 3 до 6 м. Також окремо розглядалась дія снігових та вітрових навантажень відповідно до чинного стандарту України. Обчислення проводились методом скінчених елементів на базі проектного комплексу Lira for Windows. Результати. По результатах аналізу та співставлення отриманих даних чисельних розрахунків встановлено, що найменш кошторисним є застосування сталевих оцинкованих профілів, конструкції з яких по всіх розглянутих варіантах мають найнижчу вартість. Сталеві арки на основі електрозварних прямошовних труб виявляються приблизно на 50…80 % дорожчими, а арки на основі безшовних гарячедеформованих труб – в середньому втричі дорожчими. При цьому до уваги приймалась як усереднена ринкова вартість профілів, так і вартість виготовлення з них аркової конструкції. Наукова новизна. Визначено найбільш ефективний тип сталевих сортаментних профілів для використання в аркових спорудах, що є несучими елементами каркасів легких швидкомонтованих будівель. Зокрема доведено високу ефективність сучасних тонкостінних оцинкованих профілів для даного типу конструкцій. Практична значимість. В ході досліджень отримано інженерні дані щодо конкретних типів тонкостінних оцинкованих профілів, які необхідно застосовувати для несучих аркових елементів швидкомонтованих будівель. Дані представлені в зручній для користування в інженерній практиці табличній формі в залежності від природно-кліматичних навантажень, прольотів та кроків несучих елементів каркасу таких будівель.

31 March 2020 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
YHYukhym Hezentsvei
Yukhym Hezentsvei
DBDmytro Bannikov
Dmytro Bannikov
In accordance with the recommendations of specialized professional literature, steel pyramidal-prismatic bunkers are projected for a service life of 20 years. However, in practice this term is often twice, or even three times lower. This is especially true for complicated operating conditions, in particular the effect of increased loads and low temperatures. Existing design techniques for such structures, both in European practice and the design practice of Ukraine and other CIS countries do not pay attention to these aspects. Therefore, in the practice of operation, the increased accident rate of steel bunker capacities has already become virtually a common occurrence. One of the possible ways to solve this problem is presented, which consists of using instead of traditional steels of ordinary strength with high plastic properties, steels of increased or high strength with reduced plastic properties. At the same time, clear theoretical recommendations are provided for choosing the right steel depending on the operating conditions, primarily when exposed to increased loads. The recommendations are presented in a form convenient for practical engineering applications. The proposed approach allows to reduce the material consumption of structures of this type on average according to theoretical estimates by 25-30% without reducing their bearing capacity. Their durability is also further enhanced by improving performance at low temperatures. Thus, the applied aspect of such a solution to this above problem is the possibility of increasing the overall reliability of steel bunker capacities, as well as reducing the cost of their periodic maintenance and repair work. A practical illustration of the presented approach is also given on the example of the design of bunkers of a bypass track for supplying charge materials for blast furnaces of one of the metallurgical plants of the northern location. As a result, this created the preconditions for monetary savings of about 0.5 million UAH in prices 2019 (about 20,000 USD)

1 June 2008 in Russian Metallurgy (Metally)
Verified
Journal Article
Closed access
PDF file
IVI. A. Vakulenko
I. A. Vakulenko
OPO. N. Perkov
O. N. Perkov
The effect of the morphology and size of iron carbide in a high-carbon steel on the fatigue strength and critical crack opening is considered. The increase in the fatigue strength induced by a decrease in the pearlite size in medium-and high-carbon steels is caused by the fact that the time of formation of nonuniformities in a uniform dislocation distribution shifts toward high total strains.

6 May 2020 in E3S Web of Conferences
Verified
Conference Paper
Open access
PDF file
ODOlha Dubinchyk
Olha Dubinchyk
DBDmytro Bannikov
Dmytro Bannikov
VKVitalii Kildieiev
Vitalii Kildieiev
VKVitalii Kharchenko
Vitalii Kharchenko
The article highlights results of the geotechnical analysis of the stress and strain state for the base of a subsoil massif under its interaction with the strip foundations. The massif is represented by loess soils which while soaking give overtime subsidences that complicate the operation of a building or a structure. Through geotechnical iterative research, optimization of the parameters for strip foundations on four axes at a four-storeyed residential building is carried out. Checks are performed on two groups of limiting states for scenarios of soil occurrence in natural, moistened and compacted states. The optimum dimensions in the width of strip foundations are selected, they give approximately the same strain values of the base after the creation of the soil bedding with its layer-bylayer compaction. The relevance of this research is to develop optimal parameters in the design of strip foundations for shallow depth on subsidental loess soils.