5 April 2024 in Microscopy and Microanalysis
In this article, porous GaN distributed Bragg reflectors (DBRs) were fabricated by epitaxy of undoped/doped multilayers followed by electrochemical etching. We present backscattered electron scanning electron microscopy (BSE-SEM) for sub-surface plan-view imaging, enabling efficient, non-destructive pore morphology characterization. In mesoporous GaN DBRs, BSE-SEM images the same branching pores and Voronoi-like domains as scanning transmission electron microscopy. In microporous GaN DBRs, micrographs were dominated by first porous layer features (45 nm to 108 nm sub-surface) with diffuse second layer (153 nm to 216 nm sub-surface) contributions. The optimum primary electron landing energy (LE) for image contrast and spatial resolution in a Zeiss GeminiSEM 300 was approximately 20 keV. BSE-SEM detects porosity ca. 295 nm sub-surface in an overgrown porous GaN DBR, yielding low contrast that is still first porous layer dominated. Imaging through a ca. 190 nm GaN cap improves contrast. We derived image contrast, spatial resolution, and information depth expectations from semi-empirical expressions. These theoretical studies echo our experiments as image contrast and spatial resolution can improve with higher LE, plateauing towards 30 keV. BSE-SEM is predicted to be dominated by the uppermost porous layer’s uppermost region, congruent with experimental analysis. Most pertinently, information depth increases with LE, as observed.
13 February 2025 in Journal of Physics D: Applied Physics
Ohmic contacts to wide bandgap nitrides have been realised, but little is known about their behaviour at low temperatures. To address this, an established Ti/Al/Ti/Au contact stack on AlGaN/GaN heterostructures has been characterised from 320 to 80 K. Two structures were investigated, with very similar ambient 2D electron gas transport characteristics despite their difference in AlGaN barrier thickness and composition. This allowed for direct comparison of contact behaviour across different heterostructures. Upon annealing at <800 °C for samples with 29 nm AlGaN barriers, contacts which had Ohmic characteristics at room temperature exhibited a gradual onset of Schottky behaviour as the measurement temperature was lowered. When non-Ohmic behaviour was observed, a combination of direct tunnelling, Fowler–Nordheim tunnelling and a thermally assisted Fowler–Nordheim mechanism is suggested to describe the carrier transport. In this case, annealing at 800 °C for 30 s proved sufficient to ensure Ohmic behaviour when tested from 320 to 80 K. For a heterostructure with 8 nm AlGaN, the required annealing temperature to maintain consistent Ohmic behaviour across the temperature range was reduced to 750 °C. From these observations, the determining factor for Ohmic behaviour is suggested to be the thickness of the AlGaN barrier–either as-grown, or the effective thickness following the formation of TiN protrusions into the AlGaN barrier during annealing. The understanding provided here allows tailoring of either the processing conditions or the heterostructure, and may aid with design of novel devices for low temperature operation.
3 June 2024 in Applied Physics Letters
Hyperspectral scanning capacitance microscopy (SCM) measures dC/dV−V spectra at every XY location of a semiconductor sample surface area. We report its application to GaN-based high electron mobility transistor (HEMT) structures to map threshold voltage (Vth) at the nanoscale. The consistency between the conventional SCM data and the hyperspectral SCM data set of the same area on the HEMT surface provides evidence for the reliability of hyperspectral SCM. We developed a method to extract a map of Vth distribution across the surface of the HEMT structure at the nanoscale from the hyperspectral SCM data set. The map reveals that most of the fissures (i.e., enlarged pits formed at threading dislocation surface endings) on the nitride sample surface reduce local Vth. Other variations in Vth in regions free of the fissures could be a result of thickness and/or composition inhomogeneities in the AlxGa1−xN barrier layer. Conventional SCM and other techniques cannot provide these detailed insights obtained through hyperspectral SCM.